A kit depicting the levers necessary to control isolated industrial and country sidings; contains 2 frames as illustrated. Don't forget the point rodding (SS89 and 90); catch points, ground signals/signals and loading gauges where appropriate. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Every manual Signal Box had point rodding extending to all the turnouts under its' control, an interesting extra detail that will make your layout more realistic. Kit includes 1120mm of rodding plus support cradles, cranks and other details.Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

This Plate Girder Bridge kit can be made up to suit the length of span required, and is therefore particularly useful where roads/ railways cross at an angle other than 90 degrees or where a long bridge is required. Maximum girder length 352mm. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A more modern trackside detail, concrete trunking (SS87) would carry the cabling along the lineside between boxes. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Pack contains 1460mm of Fencing and 4 Gates. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

A truly versatile kit that can be made up in many different formats. The door/window and shutter positions can be swapped around, or left as blank wall. It is easy, for example, to place them in the unit ends, where the shutters could allow trains to enter to make the unit into an EMU/DMU/Diesel Depot. This kit can be made up in full or half relief, and an extension kit (SSM315) is available to make it wider. Multiple kits can easily be joined together to make a building that is limited only by your imagination. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 168mm x 168mm (Stand Alone Format) or 336mm x 84mm (Half Relief Format)

This model can be used to add interest to a rural scene; also useful for wargamers. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 57mm x 49mm

Seen at many stations as well as at schools and factories. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 74mm x 37mm.

A typical building provided by local authorities in parks and public places. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 77mm x 56mm

Can be extended by adding additional kits and the SS83 Piers, or with the SS81 Extra Arch and Pier. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 423mm Long, 124mm Wide and 234mm High.

The Craftsman series from Wills offers the more experienced modeller a cost effective way to make large, highly individual models. They cover a range of typically British buildings both railway and domestic; each kit includes plastic moulded materials sheets, detailed parts, illustrated instructions and templates. The use of sheet materials rather than moulded parts for the main components allows the opportunity to easily modify the design to suit your needs. Should you wish to extend the building the same materials sheets are available separately (see the Wills Materials Pack range). Similarly it would be easy to add additional doors and/or windows if required.

A pair of abutments with 4 wing walls. Designed for use with the SS57 Vari Girder kit, LK-10 and 11 Girder Bridge sides and the SS26 Victorian style bridge but suitable for any bridge project. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 202mm x 96mm

A traditional barn building, for storing crops or farm machinery; the Farmyard Junk Set SSAM100 will help set the scene. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 103mm x 68mm.

The Craftsman series from Wills offers the more experienced modeller a cost effective way to make large, highly individual models. They cover a range of typically British buildings both railway and domestic; each kit includes plastic moulded materials sheets, detailed parts, illustrated instructions and templates. The use of sheet materials rather than moulded parts for the main components allows the opportunity to easily modify the design to suit your needs. Should you wish to extend the building the same materials sheets are available separately (see the Wills Materials Pack range). Similarly it would be easy to add additional doors and/or windows if required.

A single track Bow Plate Girder Bridge, includes stone abutments. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 203mm x 63mm

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

This classic Brick Arch Bridge can easily be made into a multiple arch structure with additional kits. Footprint 133mm x 70mm, (180mm x 190mm including wing walls). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Scratch and Kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
• 4 Semi - Circular brick arches - Internal Diameter 59mm, External Diameter 79mm
• 4 Semi - Circular brick arches - Internal Diameter 39mm, External Diameter 53mm
• 4 Semi - Circular brick arches - Internal Diameter 20mm, External Diameter 33mm
• 16 Window Arches - Length 13mm

Often seen with business premises in them, these Brick Retaining Arches measure 494mm long x 100mm high. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

This single track Tunnel Mouth is 133mm wide x 108mm high; total footprint is 180mm x 72mm including wing walls. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Scratch and Kit builders accessory pack. This kit contains:
• 24 Tall chimney pots
• 24 Short chimney pots
• 2 Large chimney stack cappings (Takes 4 pots)
• 2 Small chimney stack cappings (Takes 2 pots)
• 8 x 80mm lengths of round roof ridges
• 8 x 80mm lengths of angled roof ridges
• 8 x 80mm lengths of chimney stack trim
• 16 x 80mm lengths of guttering
• 8 x 80mm lengths of small down pipes
• 8 x 80mm lengths of large down pipes
• 4 x 80mm lengths of barge board strips
• 2 x 80mm lengths of window sill strips
• 8 down pipe hoppers
• 8 wall tie plates
• 4 soot/drainage manhole covers

A typical rural bus shelter to add interest to a village or small town scene. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 52mm x 35mm.

Used to allow cattle or storm water to pass through an embankment. Pack of 2. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 64mm x 60mm plus wing walls.

Useful for 'installing' CCTV around your model factories, distribution depots, or prisons!

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Can be used to extend the SS15 Coal Yard kit or to provide coal facilities in the engine shed. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 104mm x 53mm.

Coal facilities were essential at all stations in the steam era; for heating, supplies for the area and for locos. A larger coal yard can be made by adding more SS17 coal bunkers. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint:122mm x 50mm.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
• 20 24mm wide Concrete Fencing panels including post
• 20 22mm wide Ornate Concrete Fencing panels including post
• 20 22mm wide Concrete Balustrade Fencing panels including post
• 20 22mm wide Concrete Post and Rail panels including post
• 8 24mm wide Double Gates including 2 posts
• 8 14mm wide Single Gates Including 2 posts

Carries the cable between Relay boxes (SS85 and 88) and Control Centres. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Add a conservatory to a property on your layout. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 55mm x 33mm

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of vacuum formed clear plastic.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of vacuum formed clear plastic.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These corrugated iron buildings can now often be found fulfilling other functions; retail, storage or even domestic. With a little adaptation it would make a fine narrow gauge engine shed. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 123mm x 72mm

The Craftsman series from Wills offers the more experienced modeller a cost effective way to make large, highly individual models. They cover a range of typically British buildings both railway and domestic; each kit includes plastic moulded materials sheets, detailed parts, illustrated instructions and templates. The use of sheet materials rather than moulded parts for the main components allows the opportunity to easily modify the design to suit your needs. Should you wish to extend the building the same materials sheets are available separately (see the Wills Materials Pack range). Similarly it would be easy to add additional doors and/or windows if required.

The Craftsman series from Wills offers the more experienced modeller a cost effective way to make large, highly individual models. They cover a range of typically British buildings both railway and domestic; each kit includes plastic moulded materials sheets, detailed parts, illustrated instructions and templates. The use of sheet materials rather than moulded parts for the main components allows the opportunity to easily modify the design to suit your needs. Should you wish to extend the building the same materials sheets are available separately (see the Wills Materials Pack range). Similarly it would be easy to add additional doors and/or windows if required.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.