Often seen with business premises in them, these Brick Retaining Arches measure 494mm long x 100mm high. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A model of a fixed height derrick type jib crane, usually hand worked. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 81mm x 21mm.

A single track Decked Girder Bridge, includes stone abutments.Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 205mm x 67mm

Based on the Saxby and Farmer design seen on many railways across Britain. Footprint: 90mm x 56mm + 40mm over staircase. The Ratio Signal Box Interior kit 553 will provide a wealth of interior detail. Don't forget SS89 Point Rodding, SS22 Lamp Huts and, of course, signals! Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A single track Bow Plate Girder Bridge, includes stone abutments. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 203mm x 63mm

Scratch and Kit builders accessory pack. This kit contains:
‚Ģ 24 Tall chimney pots
‚Ģ 24 Short chimney pots
‚Ģ 2 Large chimney stack cappings (Takes 4 pots)
‚Ģ 2 Small chimney stack cappings (Takes 2 pots)
‚Ģ 8 x 80mm lengths of round roof ridges
‚Ģ 8 x 80mm lengths of angled roof ridges
‚Ģ 8 x 80mm lengths of chimney stack trim
‚Ģ 16 x 80mm lengths of guttering
‚Ģ 8 x 80mm lengths of small down pipes
‚Ģ 8 x 80mm lengths of large down pipes
‚Ģ 4 x 80mm lengths of barge board strips
‚Ģ 2 x 80mm lengths of window sill strips
‚Ģ 8 down pipe hoppers
‚Ģ 8 wall tie plates
‚Ģ 4 soot/drainage manhole covers

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 864mm of Rustic Fencing
‚Ģ 1272mm of Picket Fencing

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 20 26mm wide Fence Panels including post
‚Ģ 4 12mm wide Gates including post plus 8 additional posts.

Scratch and Kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 3 assorted domestic doors plus optional assorted door surrounds
‚Ģ 12 assorted domestic window frames plus optional assorted window surrounds

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 15 39mm wide Fence Panels including post
‚Ģ 5 13mm wide Gates including post plus 10 additional posts.

This scrapyard kit includes a stone shack and some ready made scrap.Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 98mm x 46mm

Level crossing keepers were often provided with a small house, so that the keeper was on hand 24 hours a day. The kit is also suitable for use as a gate lodge to a counrtry estate or in an urban park for the Park Keeper. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 98mm x 98mm

Used to allow cattle or storm water to pass through an embankment. Pack of 2. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 64mm x 60mm plus wing walls.

Street traders use theese type of stalls to sell a whole range of produce from fruit and vegeatables through to clothing and household goods. 2 carts in each pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 41mm x 21mm each.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 8 135mm long Stone Wall sections
‚Ģ 4 139mm long Capping Stone sections
‚Ģ 8 Pillar/Corner trims

This distinctive prefabricated corrugated iron building was used by the GWR as a passenger platform shelter and a storage hut. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 62mm x 39mm.

A raised water supply for an engine shed or to supply platform water cranes (See Ratio 413 and Peco LK-2 Water Cranes, also Ratio 550 Water Troughs). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 66mm x 55mm.

A building to complement the SSAM101 Blacksmith Set. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 84mm x 55mm.

A traditional barn building, for storing crops or farm machinery; the Farmyard Junk Set SSAM100 will help set the scene. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 103mm x 68mm.

Underpass for single track to be used by farm and light traffic; stone abutments included. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Span 70mm

A spartan passenger station seen in rural areas, a shelter is provided for waiting passengers. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 220mm x 50mm.

Model of a Victorian style cast iron bridge, designed to be used with the SS64 abutments kit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Span: 110mm

A spartan passenger station seen in rural areas. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 185mm x 30mm.

Add a conservatory to a property on your layout. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 55mm x 33mm

Seen at many stations as well as at schools and factories. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 74mm x 37mm.

Used to store oil for the signal lamps away from the signal box. Kit includes 2 huts and 4 barrels. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 44mm x 37mm each.

Kit includes 2 large hoardings plus 3 smaller ones, Bill Stickers himself plus ladder and paste bucket, plus a sheet of 40 posters. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 58mm x 32mm each.

Footprints: Greenhouse 56mm x 41mm, Cold Frames 26mm x 25mm each (glazing included). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

2 huts and a privy as seen on allotments everywhere. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Combined footprint: 94mm x 38mm

A parade of shops for the station approach or under the railway embankment. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 138mm x 9mm

Can be used to extend the SS15 Coal Yard kit or to provide coal facilities in the engine shed. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 104mm x 53mm.

Coal facilities were essential at all stations in the steam era; for heating, supplies for the area and for locos. A larger coal yard can be made by adding more SS17 coal bunkers. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint:122mm x 50mm.

An extra scene for the station forecourt, industrial area, or layby. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 58mm x 42mm.

Timber style garage to store a single car. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 68mm x 56mm.

A 1930's style garage and petrol station. Pumps included. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 114mm x 84mm.

These distinctive huts were once a common sight in town centres and at larger railway stations. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 93mm x 47mm.

This type of urinal, consisting of cast iron screens but otherwise open to the elements was found at busy locations in city centres and railway stations. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 92mm x 34mm.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

A more modern trackside detail, concrete trunking (SS87) would carry the cabling along the lineside between boxes. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Carries the cable between Relay boxes (SS85 and 88) and Control Centres. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Ideal for bringing a road or path over a small river or canal. The Wills scenic series provides a range of simple to make kits that help to change your layout into a model railway that contains real life detail. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Height 68mm.

Extension pack for the SS80 Viaduct kit. 141mm Long, 124mm Wide and 234mm High. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Can be extended by adding additional kits and the SS83 Piers, or with the SS81 Extra Arch and Pier. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 423mm Long, 124mm Wide and 234mm High.

This single track crossing features one of the many different types of gates used where roads had to cross the railway on the level. Kit includes 1 pair of gates 95mm x 17mm, plastic cobblestone roadway and a planked crossing deck.Don't forget the crossing keepers box (SS29), Signal Box (SS48), or Cottage (SS39). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

The platelayers who maintained the track used huts like these for storing tools, shelter - and, of course, for somewhere to make a brew! Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 58mm x 44mm.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 20 24mm wide Concrete Fencing panels including post
‚Ģ 20 22mm wide Ornate Concrete Fencing panels including post
‚Ģ 20 22mm wide Concrete Balustrade Fencing panels including post
‚Ģ 20 22mm wide Concrete Post and Rail panels including post
‚Ģ 8 24mm wide Double Gates including 2 posts
‚Ģ 8 14mm wide Single Gates Including 2 posts

Underpass for double track to be used by farm and light traffic; stone abutments included. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Span 70mm