This unit has a 12vDC 2 amp output with a 3-pin UK plug connected for mains supply. The output is via a 2-pin terminal block so will connect directly to our PL-55 Pecolectrics Turntable Motor, and also to the PLS-100 Pecolectrics SmartSwitch. It will be the perfect accessory to accompany these products

TwistLock Twin Microswitch to be used with PL-1000 for option to switch polarities, or to operate signals or panel lights etc. Easy to fit to PL-1000, simply twist and lock onto Twistlock point motor.

TwistLock a basic electric solenoid motor, for operating (in the main) turnouts and Microswitch for option to switch polarities, or to operate signals or panel lights etc.

It is powered by a normal 16vAC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard.

Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed.

Dimensions

Length = 42mm

Hook to Hook = 42mm

Depth = 25mm

Depth with twin Microswitch = 66mm

Extension Pin = 72mm

TwistLock a basic electric solenoid motor, for operating (in the main) turnouts.

It is powered by a normal 16vAC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard.

Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed.

Dimensions

Length = 42mm

Hook to Hook = 42mm

Depth = 25mm

Extension Pin = 72mm

Non-indexing turnatable motor (which means that there are no pre-set or programmable settings) means that the modeller can simply line up the deck against the exit or entrance road by eye, and the controls allow for small adjustments should things not align perfectly. This gives the modeller ultimate flexibility and control, and means that existing turntables on layouts can easily accommodate the new motor without any major track re-laying exercise! Power has to be provided from an independent 12vDC 2 amp supply, but other than that everything needed is included. Operating the motor is straightforward: you press and hold either of the clockwise or anti-clockwise buttons to rotate the deck and release the button when you wish to stop.

This turntable motor can be fitted to all existing PECO turntable kits (N, OO/HO, O-16.5, SM-32, HOm). Instructions on fitting and use are included.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

Base unit for use with the PL-10E Turnout Motor. Fixing screws and full instructions included.

Pick up and other electrical problems solved; can be used with most plastics.

Look after your model collection with this extremely useful kit, one handy pack has the things you need for basic cleaning and lubrication. The Kit contains Power Lube, Wheel Cleaning Brush and Scraper and the Locomotive Servicing Cradle which enables locomotives and rolling stock to be held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.

Locomotives and rolling stock are held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.