BROWSE PECO PRODUCTS
Browse through our complete product portfolio.
68 Products Found
Power Supply Unit
This unit has a 12vDC 2 amp output with a 3-pin UK plug connected for mains supply. The output is via a 2-pin terminal block so will connect directly to our PL-55 Pecolectrics Turntable Motor, and also to the PLS-100 Pecolectrics SmartSwitch. It will be the perfect accessory to accompany these products
Twistlock Twin Microswitch
TwistLock Twin Microswitch to be used with PL-1000 for option to switch polarities, or to operate signals or panel lights etc. Easy to fit to PL-1000, simply twist and lock onto Twistlock point motor.
Twistlock Motor and Microswitch
TwistLock a basic electric solenoid motor, for operating (in the main) turnouts and Microswitch for option to switch polarities, or to operate signals or panel lights etc.
It is powered by a normal 16vAC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard.
Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed.
Dimensions
Length = 42mm
Hook to Hook = 42mm
Depth = 25mm
Depth with twin Microswitch = 66mm
Extension Pin = 72mm
Twistlock Motor
TwistLock a basic electric solenoid motor, for operating (in the main) turnouts.
It is powered by a normal 16vAC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard.
Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed.
Dimensions
Length = 42mm
Hook to Hook = 42mm
Depth = 25mm
Extension Pin = 72mm
Turntable Motor
Non-indexing turnatable motor (which means that there are no pre-set or programmable settings) means that the modeller can simply line up the deck against the exit or entrance road by eye, and the controls allow for small adjustments should things not align perfectly. This gives the modeller ultimate flexibility and control, and means that existing turntables on layouts can easily accommodate the new motor without any major track re-laying exercise! Power has to be provided from an independent 12vDC 2 amp supply, but other than that everything needed is included. Operating the motor is straightforward: you press and hold either of the clockwise or anti-clockwise buttons to rotate the deck and release the button when you wish to stop.
This turntable motor can be fitted to all existing PECO turntable kits (N, OO/HO, O-16.5, SM-32, HOm). Instructions on fitting and use are included.
Power Feed Joiners (Pack of 8)
204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.
Power Feed Joiners (Pack of 8)
204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.
Power Feed Joiners (Pack of 8)
204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.
Smartswitch Stationary Decoder
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Stationary Decoder provides an interface between a Smartswitch Control Board and a DCC control system to enable the operation of turnouts, semaphore signals, crossing gates etc through a DCC controller. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
Smartswitch 1m Cable Extension (Pack of 2)
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Extension cable allows a servo to be located up to a metre further away from the Control Board. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
Smartfrog V6
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Smartfrog unit facilitates changing frog polarity when using the Smartswitch system to operate turnouts. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
Smartswitch Single Servo Motor
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Servo can be used in conjunction with the PLS-120 Control Board. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
Smartswitch Set
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This set contains 4 Servos, operating wires, mounting brackets and switches plus a Smartswitch Control Board, Programming Board and also the all important Instruction Manual. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
Smartswitch Control Board
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Control Board will facilitate the control of up to 4 Servos. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
Turnout Motor Mounting Plates PL-10E series
Base unit for use with the PL-10E Turnout Motor. Fixing screws and full instructions included.
G scale Turnout Motors Mounting Plate
Enables an LGB(TM) motor to be fitted to a Peco G45 Turnout.
Locomotive Servicing Kit
Look after your model collection with this extremely useful kit, one handy pack has the things you need for basic cleaning and lubrication. The Kit contains Power Lube, Wheel Cleaning Brush and Scraper and the Locomotive Servicing Cradle which enables locomotives and rolling stock to be held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.
Locomotive Servicing Cradle
Locomotives and rolling stock are held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.
Wheel Scraper
Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.
Turnout Switch Module Add-on
Allows the PL-50 Switch Module to be extended to any size required.
Turnout Switch Module
Enables switches to be connected without any need for soldering. Power is supplied through the fitted leads and each switch is automatically connected when fitted. Simply push the button on the front to open the holes, and feed in the bare wires from the turnout motor - no soldering or other fixing required. The PL-51 allows the PL-50 module to be extended to any size required.
Wheel Cleaning Brush
Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.
Terminal Block
Invaluable wiring aid - no soldering required. 2 strips of 12 blocks, easily cut with a craft knife into smaller units. Use them when extending wiring runs from Power Feed joiners (PL-80/81 and 82), Wiring Looms (PL-34) etc.