Single Pole On/Off Switch. Use this to control features such as lighting circuits, or as a section switch where only 1 controller is used.

Clip this unit either side of an insulation gap on Peco H0/00 track. This can be used to isolate a loco at the end of a terminal road or siding, thereby enabling another loco to take the stock out. This is available as a ready made item in the Peco 00 Setrack range (ST-205/2005).

A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.

This plugs directly into a ready made recess on the 0 gauge Double Slip SL-E790BH to house a PL-33 Microswitch to operate the polarity switching.

This fits directly to the PL-10 family of Turnout Motors. The 2 single pole changeover switches can be used to control polarity, route selection diagrams, or 2 aspect colour light signalling etc. Rated 16v 2amps (continuous) or 2.5amps (momentary).

A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.

Attaches directly to the PL-10 family of Turnout Motors with contact adhesive. This single pole switch can control frog polarity, ground signals etc. PL-31 Spade Connectors can be used to attach wires to these units without the need for soldering.

2 Adaptor Bases are included, with optional extension arms, to enable PL-10 Turnout Motors to be mounted on the surface of the baseboard. This unit relies on the over centre spring in the turnout to keep the blades against the stock rail.

This unit enables a PL-10 Turnout Motor to be mounted on the surface of the baseboard, an optional extension arm is also included. A removable over centre spring is fitted, useful for turnouts which do not have this feature.

Clips directly into a Peco 00/H0 Setrack Turnout, either Left or Right Hand. No holes to drill, and this unit is pre wired. Can also be used with 00/H0 Streamline Turnouts.

The PL series of Turnout Motors is tried and tested, over the last 40 years we have sold literally millions of these motors. Simple, reliable and good value. An extended drive pin is fitted, use the PL-9 Mounting Plate to attach this unit to the underside of the baseboard. Attaching PL-13 and 15 Switches will enable switching for automatic polarity etc.

The PL series of Turnout Motors is tried and tested, over the last 40 years we have sold literally millions of these motors. Simple, reliable and good value. Requires a rectangular hole 40mm x 24mm when clipped directly to the underside of a Peco Turnout. Use the PL-12/12X if above baseboard mounting is required; attaching PL-13 and 15 Switches will enable switching for automatic polarity etc.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
‚Ģ 5 500mm long OHLE Contact Wires for use with the LC-100 Catenary System 12 Mast Pack and LC-110 Catenary System Mast.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
‚Ģ 5 380mm long OHLE Contact Wires for use with the LC-100 Catenary System 12 Mast Pack and LC-110 Catenary System Mast.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
‚Ģ 5 340mm long OHLE Contact Wires for use with the LC-100 Catenary System 12 Mast Pack and LC-110 Catenary System Mast.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
‚Ģ 5 260mm long OHLE Contact Wires for use with the LC-100 Catenary System 12 Mast Pack and LC-110 Catenary System Mast.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
‚Ģ 5 200mm long OHLE Contact Wires for use with the LC-100 Catenary System 12 Mast Pack and LC-110 Catenary System Mast.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. Contact wires available separately (Refs LC-150 - 4). This pack includes:
‚Ģ 12 Masts plus push on - push off hangars (additional masts available separately Ref. LC110)
‚Ģ 2 Installation Jigs (also available separately Ref LC-115)
‚Ģ Comprehensive Installation Guide (Available separately as SYH-26 Modelling Overhead Catenary)

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
‚Ģ An additional Mast plus push on/push off hangar to extend the LC-100 Catenary System Startup Pack.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available.
‚Ģ The Installation jig is for use when installing the OHLE Catenary system. N.B. 2 of these jigs are included in the LC-100 Catenary System Startup Pack.