Transfers (Waterslide) GWR/BR from Kits PS30-32)

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four pairs of 3- link couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

Kit and Scratch builder's accessory. Pack contains 2 pairs of couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

Kit and Scratch builder's accessory. Pack contains sufficient parts for 2 pairs of Couplings. The "Instanter" coupling is a development of the standard 3 link coupling. The middle link of the chain is specially shaped so that when lying flat it provides enough slack to make coupling possible, but when this middle link is rotated 90 degrees the length of the chain is effectively shortened, reducing the amount of slack to provide closer coupling, to allow the use of train brake pipes without the need to wind a screw. It can also be coupled from the side of the wagons using a shunter's pole; much safer than having to go between vehicles when coupling them together.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains a pair of metal pin point axles plus bearings, and 3 hole disc wheels featuring free running metal rims on moulded centres.

Transfers (Pressfix) GWR/BR 'B' Container (from kit PS39)

Transfers (Waterslide) SR/BR (from kits PS100-101)

Pack of 6 standard type bicycles

Transfers (Waterslide) Black Background Patches (Pack of 5)

From Kit PS20

BR 12 ton Pipe Wagon Transfers: 1950s and 1960s/70s periods (from Kit PS17)

This is a well-known vehicle, derived from the final LNER Fish van design. BR built 1,000 of them. After fish traffic ended they were converted to Parcels Vans (SPV) and lasted into the 1980s. The kit allows both oil and roller bearing axle box versions to be built. Transfers for BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

These wagons were designed to carry heavy cast iron or steel pipes for water and drainage works. This kit represents one of 350 built in 1955. Withdrawn between late 70s and early 80s. Transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

The sloped sided design evolved from pre-1939 private owner wagons built by Chas. Roberts and Co. After the liberation of France 2,500 were shipped over there, 1,900 later returning. Around 10,000 were in stock with BR, with withdrawal taking place in the 1960s. Some ended up private industry use. Transfers for BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

The definitive BR standard mineral wagon produced in vast quantities during the 1950s, and used well in to the 1980s, carrying coal, scrap metal and many different minerals. Parts included for Instanter couplings and double brake gear. Transfers for early, late and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

6,000 were built at the end of the Second World War for service in France. They returned to the UK later in the 1950s and remained in use into the 1960s. Many were then sold into private industry use. Transfers for BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

Built in their hundreds of thousands and seen all over the rail system, these are the wagons which replaced pre war wooden private owner wagons. With side and end doors. Easy to assemble from the correctly coloured injection moulded components (no painting necessary). Kits include Transfers. Buffers are sprung and 3-link couplings are included on all models, while the BR wagons also feature working axlebox springs and moveable brake levers. Fine scale metal tyred wheels on pin-point axles supplied, spoked for the GWR wagons or 3-hole disc for the BR types. Fully illustrated instructions included.

A fleet of specialist wagons for industrial and building sand were constructed in the early 1950s. They were designed for emptying by tipper or grab. Withdrawal started in the 1970s, some lasting in Civil Engineers service into the 1980s. Transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

These low sided wagons were used for carrying the heavy ingots of crude iron known as 'pigs' from the smelting furnace to the steelworks for refining into steel. Easy to assemble from the correctly coloured injection moulded components (no painting necessary). Kits include Transfers. Buffers are sprung and 3-link couplings are included on all models, while the BR wagons also feature working axlebox springs and moveable brake levers. Fine scale metal tyred wheels on pin-point axles supplied, spoked for the GWR wagons or 3-hole disc for the BR types. Fully illustrated instructions included.

16,800 of these wagons were constructed in the 1950s. They were widely used throughout the North East for the transport of coal. Roller bearing axle boxes were applied to some in the 1960s, options for which are in the kit, and lasted until the 1980s. Transfers for early, late and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

1,500 examples built 1950 – 1951, mainly for the transport of coal. Widely used and lasted until the 1980s. Transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

This design of wagon allowed over-sized steel plates to be carried on a trestle mounted on the wagon. These wagons remained in service into the 1970s. Kit includes securing chains and shackles. Transfers for BR 1950s – 1970s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

2,150 of this design were built in 1953 – 1956. Used to carry coal for steel works, power stations and engines sheds. Were intended as the standard mineral wagon, but were too large for many customers. Withdrawn by 1982. Transfers for BR 1950s – 1970s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

Literally just a steel box on wheels, these wagons were designed to be emptied by turning them upside down in a 'tippler' mechanism, hence there are no side or end doors. Easy to assemble from the correctly coloured injection moulded components (no painting necessary). Kits include Transfers. Buffers are sprung and 3-link couplings are included on all models, while the BR wagons also feature working axlebox springs and moveable brake levers. Fine scale metal tyred wheels on pin-point axles supplied, spoked for the GWR wagons or 3-hole disc for the BR types. Fully illustrated instructions included.

Over 4,000 built from 1951 to 1959, with some in service into the 21st century. Used for carrying ballast and engineer’s materials. Featured fold-down sides for ease of access. Includes etched brass BR region plaques and transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. Pack includes working axlebox springs, sprung buffers, 3 link couplings, floor, full brake gear with alternative types of brake lever and a choice of axleguards.

O Scale BR wagon tarpaulin, produced from a material that convincingly replicates the texture and look of canvas tarpaulins once commonly used on open wagons, to protect the contents underneath. Each product contains 3 tarpaulins.

Kit of a typical small box, often found on a branch line or controlling a main line yard.

Kit and Scratch builder's accessory. Pack contains sufficient parts for 4 Buffers

Kit and Scratch builder's accessory. Pack contains sufficient parts for 4 Buffers

Kit and Scratch builder's accessory. Pack contains sufficient parts for 4 Buffers

Detailed model of the standard British Railways type. Three plastic moulded parts which, after assembly, clip onto the rails. Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys. This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Double slips can save valuable space at station approaches, junctions etc.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

This unit can be used with small, medium, or large radius turnouts to form a double junction.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys. This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

The purpose of a Catch Turnout is to derail a vehicle before it rolls out of a siding or branch line on to a main line.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

The purpose of a Catch Turnout is to derail a vehicle before it rolls out of a siding or branch line on to a main line.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Pack of 3 0 Gauge coal loads suitable for Parkside PS30/31 and 32; also Peco W-607 Wagon kits.

6 914mm lengths of Code 124 Bullhead Rail for track and turnout construction.

6 914mm lengths of Code 143 Flat Bottom Rail for track and turnout construction.

Pioneered by the Southern Railway but since seen almost everywhere.

60 concrete effect sleepers for track construction using Code 143 Flat Bottom rail.

12 cosmetic fishplates to use at joints between Code 124 and Code 143 rails.