Level crossing keepers were often provided with a small house, so that the keeper was on hand 24 hours a day. The kit is also suitable for use as a gate lodge to a counrtry estate or in an urban park for the Park Keeper. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 98mm x 98mm

These corrugated iron buildings can now often be found fulfilling other functions; retail, storage or even domestic. With a little adaptation it would make a fine narrow gauge engine shed. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 123mm x 72mm

Add a conservatory to a property on your layout. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 55mm x 33mm

Carries the cable between Relay boxes (SS85 and 88) and Control Centres. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A Southern Railway design that will span 2 tracks and includes lamps and smoke deflectors. Glue and paints required to complete model. Span 150mm.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 20 24mm wide Concrete Fencing panels including post
‚Ģ 20 22mm wide Ornate Concrete Fencing panels including post
‚Ģ 20 22mm wide Concrete Balustrade Fencing panels including post
‚Ģ 20 22mm wide Concrete Post and Rail panels including post
‚Ģ 8 24mm wide Double Gates including 2 posts
‚Ģ 8 14mm wide Single Gates Including 2 posts

These towers are an impressive sight and were an essential feature on mainline railways. The Pecoscene ranges provide the perfect loading material, Real Coal (PS-330 -332), Limestone (PS-342 and 3), Sand (PS-344), Iron Ore (PS-340), Grey Stone (PS-300- 307), and Brown Stone (PS-310 - 317) for a quarry, mine or pit loading hopper. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint: 116mm x 92mm, Height 181mm

An essential part of every small steam loco depot, add some Peco Scene Real Coal Refs PS-330/1/2 for full effect. Supplied with pre-coloured parts although painting and/or weathering (Peco Scene PS-362 Coal Dust) can add realism; glue is required to complete this model. Footprint 60mm x 55mm

Coal facilities were essential at all stations in the steam era; for heating, supplies for the area and for locos. A larger coal yard can be made by adding more SS17 coal bunkers. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint:122mm x 50mm.

Suitable for extending the Coal Depot (Ref 532) or as a stand alone item. The Ratio 526 Coal Sacks kit and Peco Scene Real Coal Refs PS-330,1 and 2 can provide extra detailing. Glue and paints required to complete model. Footprint: 75mm x 32mm

Can be used to extend the SS15 Coal Yard kit or to provide coal facilities in the engine shed. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 104mm x 53mm.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

A common feature of country stations large and small, whilst market town cattle docks could be very large indeed. Our model is of the one at Yeovil Pen Mill (GWR) Station, Somerset. Livestock (Modelscene Cows Ref. 5100, Sheep and Lambs Ref. 5110, Pigs Ref. 5108, and Horses Ref.5105) was conveyed on British railways until around 1973, although many cattle docks remained in place unused, becoming overgrown - an interesting scenic feature. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 170mm x 110mm

Used to allow cattle or storm water to pass through an embankment. Pack of 2. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 64mm x 60mm plus wing walls.

Where carriages, multiple unit sets or modern locos are stored for cleaning and maintenance, narrow platforms are provided for access. Still widely used today alongside carriage sidings, and also within storage and maintenance facilities (See Ratio 527 Carriage Shed and Wills Modern SSM300 Modern Industrial Building and SSM315 Extension kits). Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint: 500mm long plus access steps

A typical rural bus shelter to add interest to a village or small town scene. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 52mm x 35mm.

Scratch and Kit builders accessory pack. This kit contains:
‚Ģ 24 Tall chimney pots
‚Ģ 24 Short chimney pots
‚Ģ 2 Large chimney stack cappings (Takes 4 pots)
‚Ģ 2 Small chimney stack cappings (Takes 2 pots)
‚Ģ 8 x 80mm lengths of round roof ridges
‚Ģ 8 x 80mm lengths of angled roof ridges
‚Ģ 8 x 80mm lengths of chimney stack trim
‚Ģ 16 x 80mm lengths of guttering
‚Ģ 8 x 80mm lengths of small down pipes
‚Ģ 8 x 80mm lengths of large down pipes
‚Ģ 4 x 80mm lengths of barge board strips
‚Ģ 2 x 80mm lengths of window sill strips
‚Ģ 8 down pipe hoppers
‚Ģ 8 wall tie plates
‚Ģ 4 soot/drainage manhole covers

This single track Tunnel Mouth is 133mm wide x 108mm high; total footprint is 180mm x 72mm including wing walls. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Often seen with business premises in them, these Brick Retaining Arches measure 494mm long x 100mm high. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Scratch and Kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 4 Semi - Circular brick arches - Internal Diameter 59mm, External Diameter 79mm
‚Ģ 4 Semi - Circular brick arches - Internal Diameter 39mm, External Diameter 53mm
‚Ģ 4 Semi - Circular brick arches - Internal Diameter 20mm, External Diameter 33mm
‚Ģ 16 Window Arches - Length 13mm

This classic Brick Arch Bridge can easily be made into a multiple arch structure with additional kits. Footprint 133mm x 70mm, (180mm x 190mm including wing walls). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A single track Bow Plate Girder Bridge, includes stone abutments. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 203mm x 63mm

Seen at many stations as well as at schools and factories. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 74mm x 37mm.

A traditional barn building, for storing crops or farm machinery; the Farmyard Junk Set SSAM100 will help set the scene. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 103mm x 68mm.

A pair of abutments with 4 wing walls. Designed for use with the SS57 Vari Girder kit, LK-10 and 11 Girder Bridge sides and the SS26 Victorian style bridge but suitable for any bridge project. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 202mm x 96mm