0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient parts to 'convert' one wagon to a vacuum braked vehicle; it contains Dean/Churchward short brake lever, brackets and rodding, vacuum pipes and cylinder, plus steam pipes.

Plastic moulding, detail includes rainstrips, strapping etc. to finish off a Peco Wonderful Wagon Salt Wagon or a scratchbuilding project.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains a pair of metal pin point axles plus bearings, and Railway Clearing House specification 3 foot 1¬? inch wagon 8 spoke wheels featuring free running metal rims on moulded centres.

Approx 25 bearings for pin pointed wheelsets.

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model.

Specially treated metal axles which provide insulation when used with all metal wheels.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four pairs of 3- link couplings. The "Instanter" coupling is a development of the standard 3 link coupling. The middle link of the chain is specially shaped so that when lying flat it provides enough slack to make coupling possible, but when this middle link is rotated 90 degrees the length of the chain is effectively shortened, reducing the amount of slack to provide closer coupling, to allow the use of train brake pipes without the need to wind a screw. It can also be coupled from the side of the wagons using a shunter's pole; much safer than having to go between vehicles when coupling them together.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four buffers and two 3- link couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four buffers and two 3- link couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which were used to keep the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model.

3.175mm (1/8" ) Diameter Hole (Pack of 50)

1.575mm (1/16") Diameter Hole (Pack of 50)

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model.

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model.

The original metal coupling designed for use with the SL30 uncoupler, allows a vehicle to be lifted straight from within a train without derailing adjacent vehicles.

A superb auto coupling designed for magnetic operation using the special uncoupler SL-32
‚Ģ Allows a vehicle to be lifted straight from within a train without derailing adjacent vehicles
‚Ģ Delayed action feature - after uncoupling, a vehicle can be pushed to any position
‚Ģ Supplied complete with spring, screw and adaptor moulding

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains a pair of metal pin point axles plus bearings, and 3 hole disc wheels featuring free running metal rims on moulded centres.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four pairs of 3- link couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.