Kit includes:
‚Ģ 2 x 120mm ramps (1 L/H, 1 R/H)
‚Ģ 2 large gates and 2 small gates

After loading, open wagons were checked for height using this simple gauge to ensure that loads did not hit bridges etc. and therefore were usually placed near the yard exit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Placed at the foot of platform end ramps, barrow crossings allow light goods and luggage to be transferred across a double track to an adjoining platform by railway staff. Glue and paints required to complete model.

With this kit you can add a 2nd canopy to Station Building kit (Ref 204) for use on an island platform, or alternatively as an awning on the 'taxi side' of the station building. Supplied with some pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 340mm of Straight Fencing
‚Ģ 2 x 102mm lengths of Ramp Fencing
‚Ģ 1 Large and 1 Small Gate
‚Ģ 2 Ramp Gates
‚Ģ 1 Ticket Gate

Kit and scratch builders accessory, 724mm of station canopy valancing and 6 notice boards.

These simple kit lamps can represent oil, gas or electric lamps. Supplied in a pack 4; supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model.

The 2 Trestles as supplied in kit 241 are available separately, ideal for use with Peco NB-38 and 39 Girder Bridge sides or for those who enjoy scratchbuilding and kit bashing. Footprint: 61mm x 12mm, 125mm Height

Additional piers for the 251 Viaduct kit, can also be used as supports for the NB-38 and 39 Girder Bridge Sides. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Height 88mm, width 63mm each

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 680mm of fencing.

Includes 9 non working lamps with a selection or parts to make double or single standard lamps, or wall lamps. Glue and paints required to complete model. Height 46mm.

10 Telegraph poles, these also carried railway bell codes and phone connections between signal boxes and stations as well as GPO lines. Height approx 50mm

16 Telegraph poles, these also carried railway bell codes and phone connections between signal boxes and stations as well as GPO lines. Height 100mm

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm

Stations often had these Water Cranes at the end of the platforms so the locomotives could be refilled without detaching them from the train. Also included is a coke brazier, called a 'fire devil' to keep the cast iron pipe from freezing up during the winter. These cranes were usually supplied by a large water tank (see Ratio 506 and 551 and Wills SS34 kits). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 760mm of troughs and includes relevant signboards. Use in conjunction with the large Water Tower (Ref 551). Glue and paints are required to complete this model.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 370mm of troughs and includes relevant signboards. Use in conjunction with the Large Water Tower (Ref 256). Glue and paints are required to complete this model.

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint; Weighing Deck 85mm x 50mm, hut 45mm x 35mm.

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Kit includes guttering, brass etched scales and weighing plate, barge boards, window and door; glue and paints required to complete this model. Footprint: 30mm x 15mm.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 8 x 75mm lengths of fencing
‚Ģ 16 Mounting Posts

2 huts for shelter and tool storage or with many other uses; platelayers huts, tool stores, lamp huts etc. - even garden/allotment sheds or temporary site huts. Glue and paints required to complete model. Footprint: 42mm x 32mm each

A 45mm long replication of a wooden staircase, such as would be used to provide access to a signal box or other raised office/factory areas. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

This basic crane is an essential for all station yards, often found inside goods sheds or on loading banks. Used to lift loads up to 1 ton, the boom can be swung round on its base to transfer goods from road to rail vehicles. Supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model. Base Diameter: 25mm