BROWSE PECO PRODUCTS
Browse through our complete product portfolio.
50 Products Found
Twistlock Motor
TwistLock a basic electric solenoid motor, for operating (in the main) turnouts.
It is powered by a normal 16vAC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard.
Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed.
Dimensions
Length = 42mm
Hook to Hook = 42mm
Depth = 25mm
Extension Pin = 72mm
Power Feed Joiners (Pack of 8)
204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.
Power Feed Joiners (Pack of 8)
204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.
Power Feed Joiners (Pack of 8)
204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.
Smartswitch 1m Cable Extension (Pack of 2)
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Extension cable allows a servo to be located up to a metre further away from the Control Board. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
Turnout Motor Mounting Plates PL-10E series
Base unit for use with the PL-10E Turnout Motor. Fixing screws and full instructions included.
G scale Turnout Motors Mounting Plate
Enables an LGB(TM) motor to be fitted to a Peco G45 Turnout.
Locomotive Servicing Cradle
Locomotives and rolling stock are held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.
Wheel Scraper
Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.
Turnout Switch Module Add-on
Allows the PL-50 Switch Module to be extended to any size required.
Wheel Cleaning Brush
Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.
Terminal Block
Invaluable wiring aid - no soldering required. 2 strips of 12 blocks, easily cut with a craft knife into smaller units. Use them when extending wiring runs from Power Feed joiners (PL-80/81 and 82), Wiring Looms (PL-34) etc.
Rail Cleaner
Abrasive rubber block for removing dirt and oxidisation from the rail surface. Improves running, particularly at low speeds.
Yellow Connecting Wire
The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.
Red Connecting Wire
The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.
Green Connecting Wire
The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.
Cable Clips (Pack of 20)
Keep your wiring organised and tidy with these self adhesive clips. Pack of 20 clips
Blue Connecting Wire
The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.
Black Connecting Wire
The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.
Wiring Harness for PL-10 Series Turnout Motors
Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.
Closed Microswitch
Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary). Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip.
Terminal Connectors/Shrouds
Push on Terminal Connectors and shrouds. These connectors make modification and fault finding so much easier than soldered wiring. Use them to connect the PL-38 Wire to PL-26 Passing Contact Switches, PL-22 On/Off Switches, PL-23 On/On Switches, and PL-34 Wiring Looms to PL-26 Passing Contact Switches. They can also be used when connecting wires to other items, for example, PL-13 Accessory Switches, PL-15 Twin Microswitches, PL-10 Turnout Motors, and PL-32 and 33 Microswitches.
Open Microswitch
Open type, as used on the PL-15 Twin Microswitch. Rated 16v 2amps (continuous) or 2.5amps (momentary).