Often seen supporting railway cuttings and embankments in urban areas where there is insufficient space for earth slopes. Make cuttings, yard walls or raised railway viaducts with these versatile sections. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Length 348mm, Height 35mm

This kit is modelled on the Midland Railway standard 4d box with characteristic hipped roof, and is based on the prototype at Swadlincote Junction, Leics. This timeless design lasted right up to the demise of mechanical signalling. Use the Ratio Signal Box Interior kit No. 224 for a 20 lever frame, level crossing wheel and other detail. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint 42mm x 27mm (excluding steps).

2 huts for shelter and tool storage or with many other uses; platelayers huts, tool stores, lamp huts etc. - even garden/allotment sheds or temporary site huts. Glue and paints required to complete model. Footprint: Brick Hut 28mm x 15mm, Wooden Hut 28mm x 16mm

The Southern Railway produced pre-cast concrete huts after WW2 to replace wooden huts in many locations; these were used by platelayers to store tools and for shelter. Glue and paints required to complete model. Kit includes parts for 2 huts: Larger Hut 23mm x 17mm, Smaller Hut 13mm Square

After loading, open wagons were checked for height using this simple gauge to ensure that loads did not hit bridges etc. and therefore were usually placed near the yard exit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Level Crossings were commonplace, particularly in towns and across such areas as the Fenland of Eastern England. Today most have been replaced by modern barriers. Can be used for double or single track; glue and paints required to complete model.

This modern style of crossing features 2 half barriers on each side of the track, protected by (dummy) warning lights. Can be used for double or single track; glue and paints required to complete model.

Many merchants had private sidings where they could be supplied directly by rail. This kit includes office, loading platform, hoist and can be constructed in a number of ways. The Peco range of wagon loads (e.g. NR-203 Timber Loads) for 10 and 15 ft. wagons provide realistic deliveries to these types of premises. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 85mm x 60mm

This common type of station water tower can be used either platform or ground mounted and is supplied with stove, drain, hose and etched ladder. The stove was used to stop the water freezing in the crane arm. Can also supply other platform mounted water cranes (Ratio Water Crane and Fire Devil Ref 212). Glue and paints required to complete model. Tank diameter:22mm.

In the days when everything came by rail, even the smallest goods yard would provide a facility for the local coal merchant next to a siding. This kit can easily be extended by adding more staithes using Ratio Coal Staithes kit 316. Glue and paints required to complete this model. Footprint 66mm x 23mm

These were a common feature in sidings where repairs, cleaning and maintenance were effected. This shed will cover 2 tracks and can easily be extended; the kit includes guttering and centre walkway. A versatile kit with many uses both on and off the railway. Glue and paints required to complete model. Footprint 178mm x 60mm.

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Kit includes guttering, brass etched scales and weighing plate, barge boards, window and door; glue and paints required to complete this model. Footprint: 30mm x 15mm.

This versatile building would contain a boiler to provide steam either for a pump raising water or to generate electricity for a small factory. Sometimes a short siding was provided alongside for coal deliveries. Kit includes the main building, brick chimney, water tank and outbuilding. Supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model. Footprint 95mm x 65mm

Oil depot for distribution of domestic oil, which was transferred to road vehicles to deliver to domestic customers. Kit includes hut, base and pipe fittings and can easily be extended by using the Ratio Kit 315 Oil Tanks. Glue and paints required to complete this model. Footprint 80mm x 25mm

Adds the finishing touches to any signal box (See Ratio 236 and Peco NB-3 kits); it contains all you need to fit out a typical signal box including a 20-lever frame and a level crossing operating wheel. This kit also includes etched window frames, glazing, barge boards, guttering and downpipes. Glue and paints required to complete model.

Standard GWR Signal Box, numbered 8/28b by the Signalling Record Society, installed from the 1920's up until WW2. Our kit includes interior details such as levers, stove , desk and brass etched window frames. Supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model. Footprint 60mm x 25mm

This type of canopy is to be found across the country at many stations with island and bay platforms. It will match in well with the canopy on Station Building kit (Ref 204). Several kits can easily be combined to make larger canopies. Supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model. Footprint 210mm x 43mm

This kit represents a typical Goods Shed, essential to most railway stations for the storage and transfer of dry goods to road vehicles for distribution. The Peco range of wagon loads (e.g. NR-203 Timber Loads) for 10 and 15 ft. wagons provide realistic deliveries. Supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model. Footprint 90mm x 70mm

42 sacks, 10 pallets and 24 barrels. Glue and paints required to complete model.

A Southern Railway design that will span 2 tracks and includes smoke deflectors. This kit is easily extended using additional kits; glue and paints required to complete model. Span between tracks 75mm.

Pack contains 3 x 63mm lengths of etched brass laddering and includes safety cages and fixings.

A common style of fencing found in many locations. Length: 840mm. Glue is required to complete this model.

A common style of fencing found in many locations. Length: 840mm. Glue is required to complete this model.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 356mm of fencing and includes 4 gates; the SR's modular design makes it easy to form ramp sections or follow other changes in ground contour.