This kit is a model of a typical GWR brick built signal box with a hipped roof, built between 1896 and 1921. In practice there were many small differences between individual signal boxes as they were often tailored to fit the location, a good example is on the South Devon Railway at Buckfastleigh. The Ratio Signal Box Interior kit 553 will provide a wealth of interior detail. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint: Approx 90mm x 48mm

This kit replicates the precast concrete Southern Region example, often paired with the Concrete Hut (ref 518). A Fogman, when fog or snow reduced visibility, placed detonators on the rails ahead of signals or temporary speed restrictions imposed due to works etc. to provide additional warning to train drivers. The kit also includes a set of platelayers tools. Glue and paint are required to complete this kit. Footprint 20mm x 15mm.

From the late 1960's the spread of shipping containers revolutionised the transport of goods. On the railways marshalling yards gave way to intermodal depots as containers are transferred between ships, trains and road vehicles. The Rolling Underframe kit (Ref 546A) can be added to transform this unit into a movable crane. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint; Sides 61mm wide X 125mm High, Span 153mm

Modelled on a hoist found at Plymouth Laira depot which is still in use today assisting with the maintenance of Locos and rolling stock. An Inspection Pit (Peco LK-56/156) was also often provided.The Rolling Underframe kit (Ref 546A) can be added to transform this unit into a movable crane. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint 61mm wide, Span 90mm

Used for light lifting work in goods depots and other yards. Also to be found inside goods sheds for unloading wagons. Chain included; kit requires glue and paints to complete.

Where carriages, multiple unit sets or modern locos are stored for cleaning and maintenance, narrow platforms are provided for access. Still widely used today alongside carriage sidings, and also within storage and maintenance facilities (See Ratio 527 Carriage Shed and Wills Modern SSM300 Modern Industrial Building and SSM315 Extension kits). Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint: 500mm long plus access steps

300 of these wagons were built between 1952 and 1954. They were originally fitted with steam heating, but this was later removed. Used mainly by the companies Geest and Fyffes, these vans could be part of a mixed train or a 'block load' on their way from the shipping dock. Transfers are included; glue and paints are required to complete this model.

BR built 875 of these wagons between 1954 and 1960 for use on the West Country china clay workings. The first 100 wagons were unfitted, but all were later fitted with Morton vacuum brakes. Transfers are included; glue and paints are required to complete this model. Use the Pecoscene PS-361 China Clay Dust Weathering Powder to give that 'working vehicle' look to your wagon.

Often seen supporting railway cuttings and embankments in urban areas where there is insufficient space for earth slopes. Make cuttings, yard walls or raised railway viaducts with these versatile sections. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Length 350mm, Height 45mm

Pack includes: 8 Large windows (20mm x 20mm), 2 Standard windows (9mm x 20mm) , and 6 Small (9mm x 14mm) classic Midland style signal box windows.

Pack includes: 432mm of guttering, 465mm of soffits, 4 x 71mm down pipes, 1 angled water pipe and 14 down pipe brackets.

Often, the yard foreman would have an office near the yard gate, for completing paperwork and answering the telephone (don't forget the telegraph poles [Ref 452]!). Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint: 46mm x 30mm.

Water towers with cranes were generally used on platforms and in other areas with restricted space. This kit will build either a tower with a flat top or the familiar GWR conical type. Includes stove, water crane etc. as well as etched brass chain and ladder; glue and paints required to complete model. Use the Ratio Water Crane and Fire Devil Kit 413 if further cranes are required.

Kit includes 48 coal sacks. Initially coal was transported in 12 ton wagons to railway yards. Coal merchants then transferred it to heavy duty 1 cwt sacks for supply to customers. The kit also includes weights and scales; supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model.

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint; Weighing Deck 85mm x 50mm, hut 45mm x 35mm.

Many merchants had private sidings where they could be supplied directly by rail. This kit includes office, loading platform, coal scales, hoist and 2 lamps and can be constructed in a number of ways. The Ratio 514 Pallets, Sacks and Barrels, 526 Coal Sacks kits and Modelscene 5029 Coalmen and Scales can provide extra detailing. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 160mm x 105mm

If you have a large goods yard on your layout, this would make a good mess coach for the staff. It could also be used as a dwelling or provide sleeping accomodation on a campsite. Includes clutter; glue and paints required to complete model. Footprint: 195mm x 45mm

Scratch and Kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 8 Semi - Circular brick arches - Internal Diameter 30mm, External Diameter 37mm
‚Ģ 8 Semi - Circular brick arches - Internal Diameter 7mm, External Diameter 11mm
‚Ģ 2 Circular brick window surrounds - Internal Diameter 8mm, External Diameter 13mm
‚Ģ 2 Window/Door Arches - Length 48mm

Provide a home for your locos, giving them cover from the elements and a place for repairs and maintenance. It is normal to find a water tower and coaling stage nearby (see Ratio 540, 505, 506, 551 and Wills SS34 kits), and an Inspection Pit (Peco LK-56/156) was also often provided. Can be used as either a single or through shed. Multiple kits can be joined together if required. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 176mm x 90mm

Kit and scratch builders accessory, 724mm of station canopy valancing and 6 notice boards.

A useful cover for passengers awaiting their train. Several kits can be combined to protect a long platform, they can also be used side by side. Glue and paints required to complete model. Footprint: 270mm x 52mm

The Southern Railway produced pre-cast concrete huts after WW2 to replace wooden huts in many locations; these were used by platelayers to store tools and for shelter. Glue and paints required to complete model. Kit includes parts for 2 huts: Footprint: 50mm x 38mm each

Pack of 2 which can also be used as cold frames. Approximately 32mm long and 22mm wide each. Glue and paints required to complete model.

The Southern Railway used these concrete sheds for storage of goods and animal feed. The characteristic short concrete piles raise the floor above ground level to keep out the damp and rodents. Glue and paints required to complete model. Footprint: 90mm x 70mm

30 sacks, 6 pallets and 4 barrels; useful for detailing around the Goods Shed (Ratio 534), Coal/Timber Merchants (Ratio 525), Provendor Store (Ratio 513) or station yard. Glue and paints required to complete model.

2 huts for shelter and tool storage or with many other uses; platelayers huts, tool stores, lamp huts etc. - even garden/allotment sheds or temporary site huts. Glue and paints required to complete model. Footprint: 42mm x 32mm each

Single track crossing for a landowner whose property is on both sides of the railway line. Glue and paints required to complete model.

Kit and scratch builders accessory, 100mm high chimney with cowl, hand wheels and chimney support wires.

A fairly universal design seen at many steam loco depots. The kit includes water gauge, water crane, fire buckets and lamp. Use the Ratio 413 Water Crane and Fire Devil kit if further cranes are required. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 90mm x 60mm

Usually used for storage around the station or goods yard, they often can be found being used as sheds or on farmland. Clutter included; supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 176mm x 90mm

An essential part of every small steam loco depot, add some Peco Scene Real Coal Refs PS-330/1/2 for full effect. Supplied with pre-coloured parts although painting and/or weathering (Peco Scene PS-362 Coal Dust) can add realism; glue is required to complete this model. Footprint 60mm x 55mm

Designed to be placed on a platform or as a ground level box, includes fire buckets and lamp. The Ratio Signal Box Interior kit 553 will provide a wealth of interior detail. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 65mm x 50mm

The use of old coach bodies as stores, mess huts or even homes was common. Clutter included, huge scope for adding detail to such a scene. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 115mm x 40mm

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a Southern Railway rail built signal, either as a Home, Distant or combined Home and Distant signal. Glue and paints required to complete model.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit will make either 4 separate signals, or combinations of bracket signals. It can also be used with the Pratt Truss Gantry kit (Ref 478) to provide over track signals. Glue and paints required to complete model.

Although modelled on the signal box at Highley, Severn Valley Railway, this box was designed by the private signalling firm Mackenzie and Holland, making it suitable for many areas of the country. The Ratio Signal Box Interior kit 553 will provide a wealth of interior detail. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 92mm x 51mm inc. steps.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit can make 1 signal, with combinations of bracket signals plus 4 Ground Signals. It can also be used with the Pratt Truss Gantry kit (Ref 478) to provide over track signals. Glue and paints required to complete model.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit will make either 4 separate signals, or combinations of bracket signals plus 4 Ground Signals. It can also be used with the Pratt Truss Gantry kit (Ref 478) to provide over track signals. Glue and paints required to complete model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate an LMS Round Post Distant Signal. Glue and paints required to complete model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate an LMS Round Post Home Signal. Glue and paints required to complete model.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit will make either 4 separate signals, or combinations of bracket signals plus 4 Ground Signals. It can also be used with the Pratt Truss Gantry kit (Ref 478) to provide over track signals. Glue and paints required to complete model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Junction/Bracket signal, either as a Home, Distant or combined Home and Distant signal. Glue and paints required to complete model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Home and Distant Signal. Kit includes pre-coloured signal arms, glue and paints required to complete model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Distant Signal. Kit includes pre-coloured signal arm, glue and paints required to complete model.

Makes 4 Ground Signals, glue and paints required to complete model.

Placed at the foot of platform end ramps, barrow crossings allow light goods and luggage to be transferred across a double track to an adjoining platform by railway staff. Glue and paints required to complete model.

5 Steel type street lamps, 96mm high. Glue and paints required to complete model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Home Signal. Kit includes pre-coloured signal arm, glue and paints required to complete model.