This unit has a 12vDC 2 amp output with a 3-pin UK plug connected for mains supply. The output is via a 2-pin terminal block so will connect directly to our PL-55 Pecolectrics Turntable Motor, and also to the PLS-100 Pecolectrics SmartSwitch. It will be the perfect accessory to accompany these products

TwistLock Twin Microswitch to be used with PL-1000 for option to switch polarities, or to operate signals or panel lights etc. Easy to fit to PL-1000, simply twist and lock onto Twistlock point motor.

TwistLock a basic electric solenoid motor, for operating (in the main) turnouts and Microswitch for option to switch polarities, or to operate signals or panel lights etc.

It is powered by a normal 16vAC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard.

Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed.

Dimensions

Length = 42mm

Hook to Hook = 42mm

Depth = 25mm

Depth with twin Microswitch = 66mm

Extension Pin = 72mm

TwistLock a basic electric solenoid motor, for operating (in the main) turnouts.

It is powered by a normal 16vAC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard.

Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed.

Dimensions

Length = 42mm

Hook to Hook = 42mm

Depth = 25mm

Extension Pin = 72mm

Non-indexing turnatable motor (which means that there are no pre-set or programmable settings) means that the modeller can simply line up the deck against the exit or entrance road by eye, and the controls allow for small adjustments should things not align perfectly. This gives the modeller ultimate flexibility and control, and means that existing turntables on layouts can easily accommodate the new motor without any major track re-laying exercise! Power has to be provided from an independent 12vDC 2 amp supply, but other than that everything needed is included. Operating the motor is straightforward: you press and hold either of the clockwise or anti-clockwise buttons to rotate the deck and release the button when you wish to stop.

This turntable motor can be fitted to all existing PECO turntable kits (N, OO/HO, O-16.5, SM-32, HOm). Instructions on fitting and use are included.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.

Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.

This fits directly to the PL-10 family of Turnout Motors. The 2 single pole changeover switches can be used to control polarity, route selection diagrams, or 2 aspect colour light signalling etc. Rated 16v 2amps (continuous) or 2.5amps (momentary).

Allows the PL-50 Switch Module to be extended to any size required.

Enables switches to be connected without any need for soldering. Power is supplied through the fitted leads and each switch is automatically connected when fitted. Simply push the button on the front to open the holes, and feed in the bare wires from the turnout motor - no soldering or other fixing required. The PL-51 allows the PL-50 module to be extended to any size required.

The PL series of Turnout Motors is tried and tested, over the last 40 years we have sold literally millions of these motors. Simple, reliable and good value. An extended drive pin is fitted, use the PL-9 Mounting Plate to attach this unit to the underside of the baseboard. Attaching PL-13 and 15 Switches will enable switching for automatic polarity etc.

2 Adaptor Bases are included, with optional extension arms, to enable PL-10 Turnout Motors to be mounted on the surface of the baseboard. This unit relies on the over centre spring in the turnout to keep the blades against the stock rail.

This unit enables a PL-10 Turnout Motor to be mounted on the surface of the baseboard, an optional extension arm is also included. A removable over centre spring is fitted, useful for turnouts which do not have this feature.

Clip this unit either side of an insulation gap on Peco H0/00 track. This can be used to isolate a loco at the end of a terminal road or siding, thereby enabling another loco to take the stock out. This is available as a ready made item in the Peco 00 Setrack range (ST-205/2005).

Push on Terminal Connectors and shrouds. These connectors make modification and fault finding so much easier than soldered wiring. Use them to connect the PL-38 Wire to PL-26 Passing Contact Switches, PL-22 On/Off Switches, PL-23 On/On Switches, and PL-34 Wiring Looms to PL-26 Passing Contact Switches. They can also be used when connecting wires to other items, for example, PL-13 Accessory Switches, PL-15 Twin Microswitches, PL-10 Turnout Motors, and PL-32 and 33 Microswitches.

Use these when creating a diagrammatic control panel to clip fit PL-26 Passing Contact Switches, PL-22 On/Off Switches and PL-23 On/On Switches in the required place.

Allows adjacent switches in the PL-27 Switch Console and PL-50/51 Switch Module Unit to be ganged together and operated simultaneously.

Houses 6 PL-26 Passing Contact Switches, PL-22 On/Off Switches or PL-23 On/On Switches.

A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.

The PL series of Turnout Motors is tried and tested, over the last 40 years we have sold literally millions of these motors. Simple, reliable and good value. Requires a rectangular hole 40mm x 24mm when clipped directly to the underside of a Peco Turnout. Use the PL-12/12X if above baseboard mounting is required; attaching PL-13 and 15 Switches will enable switching for automatic polarity etc.

Single Pole On/On Switch. Use this to switch power from one device to another or for operating items such as 2 aspect colour light signals.

Clips directly into a Peco 00/H0 Setrack Turnout, either Left or Right Hand. No holes to drill, and this unit is pre wired. Can also be used with 00/H0 Streamline Turnouts.

Invaluable wiring aid - no soldering required. 2 strips of 12 blocks, easily cut with a craft knife into smaller units. Use them when extending wiring runs from Power Feed joiners (PL-80/81 and 82), Wiring Looms (PL-34) etc.

Resistors for use with the PL-30 Red and Green LED's.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Abrasive rubber block for removing dirt and oxidisation from the rail surface. Improves running, particularly at low speeds.

A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.

Pick up and other electrical problems solved; can be used with most plastics.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

Open type, as used on the PL-15 Twin Microswitch. Rated 16v 2amps (continuous) or 2.5amps (momentary).

Single Pole On/Off Switch. Use this to control features such as lighting circuits, or as a section switch where only 1 controller is used.

Base unit for use with the PL-10E Turnout Motor. Fixing screws and full instructions included.

This plugs directly into a ready made recess on the 0 gauge Double Slip SL-E790BH to house a PL-33 Microswitch to operate the polarity switching.

Look after your model collection with this extremely useful kit, one handy pack has the things you need for basic cleaning and lubrication. The Kit contains Power Lube, Wheel Cleaning Brush and Scraper and the Locomotive Servicing Cradle which enables locomotives and rolling stock to be held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.

Locomotives and rolling stock are held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.

These can be used directly from terminals on the Smartswitch (TM) Control Board (PLS-120) and Smartfrog (PLS-130) to show route selection. They can also be powered via a 12v DC supply if the PL-29 Resistors are included in the circuit.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary). Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. Contact wires available separately (Refs LC-150 - 4). This pack includes:
• 12 Masts plus push on - push off hangars (additional masts available separately Ref. LC110)
• 2 Installation Jigs (also available separately Ref LC-115)
• Comprehensive Installation Guide (Available separately as SYH-26 Modelling Overhead Catenary)

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
• An additional Mast plus push on/push off hangar to extend the LC-100 Catenary System Startup Pack.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available.
• The Installation jig is for use when installing the OHLE Catenary system. N.B. 2 of these jigs are included in the LC-100 Catenary System Startup Pack.