10 ton Goods Van ‘Mink/Mink A’ V12, V14 and V16 Built between 1907 and 1927. Used for general goods traffic throughout the British railway system. In service until around 1960, later in departmental use. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

These gunpowder vans (diagram Z2) were built between 1913 and 1926 to carry gunpowder and other explosives. Examples lasted until around 1960. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

(Diagram O11/15) Over 12000 were built between 1909 and 1922. 011 had hand brake only and 015 wagons had the vacuum brake. Examples lasted into the 1950s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

7,000 of these vans were built between 1933 and 1945 for the carriage of general merchandise. Transfers are included; glue and paints are required to complete this model.

The term 'TOAD' refers to the GWR Telegraph Code for this type of vehicle. The kit includes 3 tail lamps, glazing, hand brake standard and transfers. Glue and paints are required to complete this model.

Introduced in 1924, and part of GWR’s drive to use higher capacity wagons. Known as ‘Pole’ wagons (diagram N24) after the company’s General Manager. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

Built as part of the 'common user' pool of vehicles, their numbers totalled nearly 6,000. Made between 1931 and 1934, they were heavliy used all over the system. Transfers are included; glue and paints are required to complete this model.

‘Mica B’ X7 These vans were built in 1921 - 1923 to carry fresh or chilled meat. Some vans were converted to TEVANS in the 1930s. Most survived into Nationalisation in 1948 and a few into the early 1960s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers . Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

These wagons were used for carrying rail, girders, sawn timber, trees, telegraph poles, pipes etc. 'Steel girder' load included. Transfers are included; glue and paints are required to complete this model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Distant Signal. Kit includes pre-coloured signal arm, glue and paints required to complete model.

An ideal load for a conflat or haulage vehicle, or as an accessory in a station yard or factory. Once dubbed 'the suitcase of industry' these railway containers were the precursor of the modern container, allowing a contained load to be quickly unloaded or transhipped from rail to road transport. (Pack of 2).

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Home Signal. Kit includes pre-coloured signal arm, glue and paints required to complete model.

Used first for perishable goods and later for gunpowder, these vans were also built by the LNWR, LSWR and used as private owner vans. Transfers are included; glue and paints are required to complete this model.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 36 posts and enough wire to make 720mm of fencing.

A simple kit to make this attractive half-cab Maudsley bus. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

A simple kit to make this attractive Thorneycroft vehicle. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

Built between 1933 and 1936 solely for the transport of cars. The end doors allowed cars to be driven in and out via a special unloading dock at the end of a siding. Transfers are included; glue and paints are required to complete this model.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four buffers and two 3- link couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which were used to keep the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

Pack includes parts to make a pair of these heavy duty design bogies that feature cast steel type sideframes. Kit includes bolster, wheels and tension lock couplings; supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Fencing to go at the back of a platform ramp plus 3 gates

Once dubbed 'the suitcase of industry' these railway containers were the precursor of the modern container, allowing a contained load to be quickly unloaded or transhipped from rail to road transport. All Peco wagons feature free running wheels in pin point axles. The ELC coupling, whilst compatible with the standard N gauge couplings, keeps a realistic distance between the vehicles and enables the PL-25 electro magnetic decoupler to be used for remote uncoupling.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit contains 2 posts, 2 Home arms and 1 Distant. It can also be used with the Pratt Truss Gantry kit (Ref 478) to provide over track signals. Glue and paints required to complete model.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit enables you to replicate a GWR Junction/Bracket Home signal. Glue and paints required to complete model.

Classic style fencing modelled on a GWR design, but still seen also in many other places, around parks, public buildings, monuments etc. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 484mm of fencing

Classic style fencing modelled on a GWR design, but still seen also in many other places, around parks, public buildings, monuments etc. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 2 x 56mm lengths of ramp fencing
‚Ģ 8 assorted gates

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit will make either 4 separate signals, or combinations of bracket signals plus 4 Ground Signals. It can also be used with the Pratt Truss Gantry kit (Ref 478) to provide over track signals. Glue and paints required to complete model.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 238mm of Straight Fencing
‚Ģ 2 x 56mm lengths of Ramp Fencing
‚Ģ 4 Gates

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 680mm of fencing.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 340mm of Straight Fencing
‚Ģ 2 x 102mm lengths of Ramp Fencing
‚Ģ 1 Large and 1 Small Gate
‚Ģ 2 Ramp Gates
‚Ģ 1 Ticket Gate

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 680mm of fencing.

Kit for 4 classics GWR steel and timber seats with the GWR 'shirtbutton' logo.

Fencing to go at the back of a platform plus 3 gates; also seen in public parks, Georgian terraces and many other places.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains Approximately 476mm of fencing.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four buffers and two 3- link couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

O Scale GWR wagon tarpaulin, produced from a material that convincingly replicates the texture and look of canvas tarpaulins once commonly used on open wagons, to protect the contents underneath. Each product contains 3 tarpaulins.

Transfers (Waterslide) GWR/BR (from Kits PS26-29)

Transfers (Waterslide) GWR/BR (from Kits PS23-24)

After loading, open wagons were checked for height using this simple gauge to ensure that loads did not hit bridges etc. and therefore were usually placed near the yard exit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Vacuum braked wagon underframe kit with steel type solebars. Kit and scratch builders' accessory; glue and paints are required to complete this model.

In August 2023 DB Cargo retired the last of the former BR/ECC china clay CDA hoppers after a service life of 35 years. These unique and distinctive wagons will be missed by enthusiasts but thanks to PECO, modellers can keep their legacy going in model form!

Note that the CDA wagons are now fitted with metal-tyred wheels as standard.

The CDA China Clay hopper, and the HAA Coal Hopper, are closely related, sharing the same design and operational principles, with bottom hopper doors opened to empty the contents, in the case of china clay, for loading into ships at Carne Point, near Fowey in Cornwall. As china clay must be kept dry special rolling tarpaulin covers protected the load, as featured on our models.

PECO Setrack 00 Gauge Code 100 - Unit trackage System
The high quality rigid unit trackage system suitable for all popular brands of 00 gauge model trains.
Being fully compatible with the Code 100 PECO Streamline range, it need never be discarded as your layout develops.
The solid nickel silver rails are integrally moulded into the sleeper bases for maximum realism and strength. Turnouts are fitted with an over-centre spring for immediate use, no extra levers necessary.

PECO Setrack N Gauge Code 80 - Unit trackage System
The high quality rigid unit trackage system suitable for all popular brands of N gauge model trains.
Being fully compatible with both Code 80 and Code 55 PECO Streamline, it need never be discarded as your layout develops.
The solid nickel silver rails are integrally moulded into the sleeper bases for maximum realism and strength. Turnouts are fitted with an over-centre spring for immediate use, no extra levers necessary.

PECO Setrack N Gauge Code 80 - Unit trackage System
The high quality rigid unit trackage system suitable for all popular brands of N gauge model trains.
Being fully compatible with both Code 80 and Code 55 PECO Streamline, it need never be discarded as your layout develops.
The solid nickel silver rails are integrally moulded into the sleeper bases for maximum realism and strength. Turnouts are fitted with an over-centre spring for immediate use, no extra levers necessary.

PECO Setrack 00 Gauge Code 100 - Unit trackage System
The high quality rigid unit trackage system suitable for all popular brands of 00 gauge model trains.
Being fully compatible with the Code 100 PECO Streamline range, it need never be discarded as your layout develops.
The solid nickel silver rails are integrally moulded into the sleeper bases for maximum realism and strength. Turnouts are fitted with an over-centre spring for immediate use, no extra levers necessary.

A simple kit to make this attractive Throneycroft vehicle. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

Keep on the right side of health and safety regulations - use these double rail stanchions in locations wherever the general public are allowed. Pack contains 20 injection moulded supports and approx 2 x 400mm length of nickel silver railing.

Always difficult to scratchbuild, these realistic features will enhance any industrial installation that needs a single rail safety barrier. Pack contains 20 injection moulded supports and 400mm length of brass wire.