Classic style fencing modelled on a GWR design, but still seen also in many other places, around parks, public buildings, monuments etc. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 2 x 56mm lengths of ramp fencing
‚Ģ 8 assorted gates

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 238mm of Straight Fencing
‚Ģ 2 x 56mm lengths of Ramp Fencing
‚Ģ 4 Gates

This superb kit is modelled on the overall roof at Ashburton, Devon. Designed for use with Station Building kit (Ref 204), it will enable you to build a GWR station quickly and easily. Although a specific prototype, the design is typical of many other regions including some tropical countries where it was intended to shelter passengers from the sun as well as rain. Supplied with some pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 153mm x 82mm

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains Approximately 476mm of fencing.

Standard GWR Signal Box, numbered 8/28b by the Signalling Record Society, installed from the 1920's up until WW2. Our kit includes interior details such as levers, stove , desk and brass etched window frames. Supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model. Footprint 60mm x 25mm

This kit contains the parts to make 1 Lower Quadrant Home or Distant Signal. Glue and paints required to complete model.

This kit contains the parts to make 1 Upper Quadrant Home or Distant Signal. Glue and paints required to complete model.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. Kit includes parts to make: 1 Industrial chimney approx 120mm High, 20mm x 20mm at base, and 1 Tank 24mm Long x 14mm Wide and approx 34mm High.

Etched brass Industrial style windows. This pack contains:
‚Ģ 8 11mm x 6mm Round Top Window Frames
‚Ģ 6 10mm x 6mm Round Top Window Frames
‚Ģ 4 6mm x 9mm Rectangular Windows Frames
‚Ģ 2 15mm x 12mm Skylight Frames
‚Ģ 2 3mm Diameter Porthole Window Frames
‚Ģ 4 Small half Round Window Frames

This kit contains the parts to make 1 Lower Quadrant Home or Distant Junction/Bracket Signal. Glue and paints required to complete model.

This 20,000 gallon design is equally at home replenishing water troughs (Ratio Water Troughs kit Ref 255), a large motive power depot or supplying several platform mounted water cranes (Ratio Water Crane and Fire Devil Ref 212). Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint 72mm x 30mm

This modern style of crossing features 2 half barriers on each side of the track, protected by (dummy) warning lights. Can be used for double or single track; glue and paints required to complete model.

Level Crossings were commonplace, particularly in towns and across such areas as the Fenland of Eastern England. Today most have been replaced by modern barriers. Can be used for double or single track; glue and paints required to complete model.

A common style of fencing found in many locations. Length: 840mm. Glue is required to complete this model.

A common style of fencing found in many locations. Length: 840mm. Glue is required to complete this model.

2 huts for shelter and tool storage or with many other uses; platelayers huts, tool stores, lamp huts etc. - even garden/allotment sheds or temporary site huts. Glue and paints required to complete model. Footprint: Brick Hut 28mm x 15mm, Wooden Hut 28mm x 16mm

After loading, open wagons were checked for height using this simple gauge to ensure that loads did not hit bridges etc. and therefore were usually placed near the yard exit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Complements your Engine Shed (See Ratio Kit 203). Kit includes a rectangular water tower, water crane, coaling stage with coal staithes and hoist with buckets. Supplied with some pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 90mm x 30mm.

This kit is modelled on the Midland Railway standard 4d box with characteristic hipped roof, and is based on the prototype at Swadlincote Junction, Leics. This timeless design lasted right up to the demise of mechanical signalling. Use the Ratio Signal Box Interior kit No. 224 for a 20 lever frame, level crossing wheel and other detail. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint 42mm x 27mm (excluding steps).

With it's fine scale latticework and curved section roof, this typical footbridge will add interest and a sense of importance to any model station. The versatile kit design means that the stairs can be assembled to face in either direction or straight off the end of the bridge. Moulded in 3 colours to make painting optional, the tooling of the fine lattice work sets the standard for injection moulding in this scale. Additional kits can be used to create multiple spans, whilst larger, busier stations often had 2 stairways to each platform, leading off in both directions. Could also be used without the roof sections at a large terminus under an overall station canopy. Glue is required to complete this model. Span: 93mm

Oil depot for distribution of domestic oil, which was transferred to road vehicles to deliver to domestic customers. Kit includes hut, base and pipe fittings and can easily be extended by using the Ratio Kit 315 Oil Tanks. Glue and paints required to complete this model. Footprint 80mm x 25mm

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. These Oil tanks can be used to extend the Oil Depot (ref 228) or as a stand alone feature. Footprint: 80mm x 25mm

42 sacks, 10 pallets and 24 barrels. Glue and paints required to complete model.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm