Stone edged platform with brick support will make up various combinations of platform; glue and paints required to complete model. See also Modelscene Station Staff 5059, Passengers Standing Sets A and B 5057 and 5058. Footprint: 480mm x 92mm

Kit contains parts to make a 240mm long and 40mm wide platform; easily extended by using further kits. Use Ratio Platform Ramps kit 210 with these platforms. Supplied with some pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A Gantry to support signals, such as the semaphore signals in our kits Ref 260, 262 and 270. It can also be used to mount colour light signals, and route and platform indicators. Glue and paints required to complete model.

A Gantry to support signals, such as the semaphore signals in our Advanced Construction packs Ref 466 (GWR), 476(LMS), 477(LNWR) and 486(LNER/SR). It can also be used to mount colour light signals, and route and platform indicators. Glue and paints required to complete model.

The Southern Railway used these concrete sheds for storage of goods and animal feed. The characteristic short concrete piles raise the floor above ground level to keep out the damp and rodents. Glue and paints required to complete model. Footprint: 90mm x 70mm

This versatile building would contain a boiler to provide steam either for a pump raising water or to generate electricity for a small factory. Sometimes a short siding was provided alongside for coal deliveries. Kit includes the main building, brick chimney, water tank and outbuilding. Supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model. Footprint 95mm x 65mm

This versatile building would contain a boiler to provide steam either for a pump raising water or to generate electricity for a small factory. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 110mm x 90mm

Kit contains parts to make 12 Relay Boxes. Use with Concrete Trunking (Ref 258); supplied with pre-coloured parts although painting and/or weathering can add realism. Glue is required to complete this model.

Includes a lever, cord and screw eyes - everything you need to operate one signal.

Often seen supporting railway cuttings and embankments in urban areas where there is insufficient space for earth slopes. Make cuttings, yard walls or raised railway viaducts with these versatile sections. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Length 348mm, Height 35mm

Often seen supporting railway cuttings and embankments in urban areas where there is insufficient space for earth slopes. Make cuttings, yard walls or raised railway viaducts with these versatile sections. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Length 350mm, Height 45mm

The Wills scenic series provides a range of simple to make kits that help to change your layout into a model railway that contains real life detail. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Height 68mm.

To fit under the Ratio Locomotive Lifting Hoist (545) or Overhead Traversing Crane (546) to allow them to run along tracks (not included). The kit makes a pair of rolling underframes. Length 61mm.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm

This common type of station water tower can be used either platform or ground mounted and is supplied with stove, drain, hose and etched ladder. The stove was used to stop the water freezing in the crane arm. Can also supply other platform mounted water cranes (Ratio Water Crane and Fire Devil Ref 212). Glue and paints required to complete model. Tank diameter:22mm.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 1600mm of fencing
‚Ģ Includes road and rail gates.

2 brick built chimney stacks with pots in kit form. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Adds the finishing touches to any signal box (See Ratio 236 and Peco NB-3 kits); it contains all you need to fit out a typical signal box including a 20-lever frame and a level crossing operating wheel. This kit also includes etched window frames, glazing, barge boards, guttering and downpipes. Glue and paints required to complete model.

Adds the finishing touches to any signal box (See Ratio 500, 503, 536, 552 and Wills SS48 kits); it contains all you need to fit out a typical signal box including a 20-lever frame and a level crossing operating wheel. Glue and paints required to complete model.

Pack includes 24 9mm x 16mm classic Great Western style signal box windows.

Pack contains 3 x 63mm lengths of etched brass laddering and includes safety cages and fixings.

4 x 143mm lengths of laddering.

Pack of 2 which can also be used as cold frames. Approximately 32mm long and 22mm wide each. Glue and paints required to complete model.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm