Designed for use with the SS62 Stone Paved Platform Ramps, SS78 Island Platform building, and SS54 Canopy. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint:264mm x 76mm.

2 Garden sheds, each 57mm x 28mm. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

This Plate Girder Bridge kit can be made up to suit the length of span required, and is therefore particularly useful where roads/ railways cross at an angle other than 90 degrees or where a long bridge is required. Maximum girder length 352mm. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

This classic Brick Arch Bridge can easily be made into a multiple arch structure with additional kits. Footprint 133mm x 70mm, (180mm x 190mm including wing walls). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

This 180mm long and 60mm wide Canopy is designed for use with the SS61 Platform sections and SS78 Island Platform building, but can be used with any suitable platform system. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Scratch and Kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 4 Semi - Circular brick arches - Internal Diameter 59mm, External Diameter 79mm
‚Ģ 4 Semi - Circular brick arches - Internal Diameter 39mm, External Diameter 53mm
‚Ģ 4 Semi - Circular brick arches - Internal Diameter 20mm, External Diameter 33mm
‚Ģ 16 Window Arches - Length 13mm

Often seen with business premises in them, these Brick Retaining Arches measure 494mm long x 100mm high. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A single track Decked Girder Bridge, includes stone abutments.Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 205mm x 67mm

A model of a fixed height derrick type jib crane, usually hand worked. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 81mm x 21mm.

Based on the Saxby and Farmer design seen on many railways across Britain. Footprint: 90mm x 56mm + 40mm over staircase. The Ratio Signal Box Interior kit 553 will provide a wealth of interior detail. Don't forget SS89 Point Rodding, SS22 Lamp Huts and, of course, signals! Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

A single track Bow Plate Girder Bridge, includes stone abutments. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 203mm x 63mm

Scratch and Kit builders accessory pack. This kit contains:
‚Ģ 24 Tall chimney pots
‚Ģ 24 Short chimney pots
‚Ģ 2 Large chimney stack cappings (Takes 4 pots)
‚Ģ 2 Small chimney stack cappings (Takes 2 pots)
‚Ģ 8 x 80mm lengths of round roof ridges
‚Ģ 8 x 80mm lengths of angled roof ridges
‚Ģ 8 x 80mm lengths of chimney stack trim
‚Ģ 16 x 80mm lengths of guttering
‚Ģ 8 x 80mm lengths of small down pipes
‚Ģ 8 x 80mm lengths of large down pipes
‚Ģ 4 x 80mm lengths of barge board strips
‚Ģ 2 x 80mm lengths of window sill strips
‚Ģ 8 down pipe hoppers
‚Ģ 8 wall tie plates
‚Ģ 4 soot/drainage manhole covers