SORT BY
PAGE

383 Products Found

00-9 Box Van Bass

Something a little bit different, these excellently finished ready to run wagons are fictitious and based on some of our more popular ready to run wagons in the N Gauge range.

00-9 Box Van Colman's Mustard

Something a little bit different, these excellently finished ready to run wagons are fictitious and based on some of our more popular ready to run wagons in the N Gauge range.

00-9 Box Van Fyffes Bananas

Something a little bit different, these excellently finished ready to run wagons are fictitious and based on some of our more popular ready to run wagons in the N Gauge range.

10.5mm Bogie Spoked Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

10.5mm Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

10.5mm Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

10.5mm Spoked Tender Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

12mm 3 Hole Disc Wheel

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

12mm Bogie Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

12mm Bogie Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

12mm Disc Brake Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

12mm Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

12mm Spoked Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

14mm Bogie Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

14mm Bogie Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

14mm Disc Brake Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

14mm Disc Coach Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

14mm Mansell Coach Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

14mm Tender Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

16mm Bogie Disc inside Bearing

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

16mm Bogie Spoked Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

16mm Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

16mm Tender Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

3 Link Brass Couplings

Barrel Plated. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

4 Wheel Coach 2 Compartments

These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers.

4 Wheel Coach 2 Compartments

These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers.

4 Wheel Coach Single Compartment

These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers.

4 Wheel End Door Open Wagon

These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers.

4 Wheel Goods Van

These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers.

60:1 Ratio 1/8" Bore (Gear) 3/32" Bore (Worm) Gear and Worm Set

Brass gear wheels and steel worms, drilled and tapped with 10BA fixing screws.

7mm Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

9 ft Wheelbase LN WR/LMS Wagon Underframe Kit

Contains 2 underframe kits for unfitted pre group wagon underframe with wooden type solebars. Kit and scratch builders' accessory; glue and paints are required to complete this model.

9ft/10ft Underframe Kit

These Underframe kits give a choice of a 9ft wooden or 10ft steel type Sole Bars and include:
• Actual working axlebox springs
• Sprung metal buffers
• Choice of 9 foot (wooden) or 10 foot (steel) solebars
• Pin-point axles and bearings for maximum length trains
• Both Peco Simplex and Peco Anita tension lock couplings.Romford wheels and bearings can be used to complete the model.

9mm Bogie Spoked Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

9mm Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

9mm Disc Wheels

The 00/H0 spoked wheels are cast, giving an accurate spoke profile, then turned and nickel plated. Disc and 3-hole wheels are turned in brass and plated. All wheels are insulated on both sides. Bogie wheels are mounted on axles for inside bearings, all other wheels are mounted on pin point axles.

Baddesley Coal 7 Plank

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model.

Bass Box Van

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model. An R-37 Box Van roof is also required.

Bibbington Mineral 5 Plank

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model.

Blaenavon Company Low Sided 3 Plank

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model.

Blue Circle Box Van

00 Card wagon body kits, designed to be used with the R20 Underframe kit. Romford wheels and bearings can be used to complete the model. An R-37 Box Van roof is also required.

Bolster Set

Kit and scratch builders accessory; as included in the 21 ton Twin Bolster wagon kit PC18.

Box Van Roof

Black plastic moulding, detail includes rainstrips, strapping etc. to finish off a Peco Wonderful Wagon Box Van or a scratchbuilding project.

BR 'Clam' 21ton Ballast Wagon

Built 1989-1991 on ex hopper chassis, 400 clam wagons carried mainly waste ballast. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers . Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 'Clayhood' China Wagon

BR built 875 of these wagons between 1954 and 1960 for use on the West Country china clay workings. The first 100 wagons were unfitted, but all were later fitted with Morton vacuum brakes. Transfers are included; glue and paints are required to complete this model. Use the Pecoscene PS-361 China Clay Dust Weathering Powder to give that 'working vehicle' look to your wagon.

BR (LNER Design) Plywood Goods Van

These wagons (diagram 1/176) were built by the LNER from the end of the Second World War. 3250 were constructed to this diagram. Lasted until the early 1970s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 10 foot Chassis kit, LNER Pattern Clasp Brake Shoes

Kit and scratch builders accessory, as supplied with 13 ton Steel Open Goods Wagon kit PC01A.

BR 10 foot Chassis kit, Vacuum Fitted with Clasp Brake Shoes

Kit and scratch builders accessory; as included in the 12 ton 'Vanwide' kit PC41. Includes both LMS (J' Hanger) and BR Type Spring Suspension detail.

PAGE

Trade Login

WOULD YOU LIKE TO BECOME A TRADE PARTNER?

PECO - PLEASE SUPPLY TEXT.
An introductory paragraph with criteria listed as bullets points, closing with contact call to action.