This model platform system is ideal for use with Peco N Setrack, Streamline and any other unit trackage system which conforms to the same geometry. The two sections in this pack make a 288mm long platform plus ramps; it can easily be extended by simply clipping in additional ST-93 Brick type platform units. As supplied the units fit a standard track configuration but it is easy to adapt to suit other situations; just cut the platform surfaces to any of three widths by following the scribed lines on the back. Ramps can be made to one of two widths, and have curved sides to match the Setrack curve.

Often seen with business premises in them, these Brick Retaining Arches measure 494mm long x 100mm high. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

This single track Tunnel Mouth is 133mm wide x 108mm high; total footprint is 180mm x 72mm including wing walls. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm

Plastic sheet emulating Blue Engineering Brick. Pack of 4

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Pair of detailed Bridge sides, with separate wings walls for optional positioning. Matching Stone Walling is also available (NB-40).

Pair of detailed Bridge sides, with separate wings walls for optional positioning. Matching Stone Walling is also available (NB-40).

Detailed model of the standard British Railways type. Three plastic moulded parts which, after assembly, clip onto the rails (2 per pack).

A selection of windows, doors, gutters and downpipes, stanchions, plus bench seat and ventilator

A kit containing roofs, chimneys and notice boards for kit adaptation and scratchbuilding.

Scratch and Kit builders accessory pack. This kit contains:
‚Ģ 24 Tall chimney pots
‚Ģ 24 Short chimney pots
‚Ģ 2 Large chimney stack cappings (Takes 4 pots)
‚Ģ 2 Small chimney stack cappings (Takes 2 pots)
‚Ģ 8 x 80mm lengths of round roof ridges
‚Ģ 8 x 80mm lengths of angled roof ridges
‚Ģ 8 x 80mm lengths of chimney stack trim
‚Ģ 16 x 80mm lengths of guttering
‚Ģ 8 x 80mm lengths of small down pipes
‚Ģ 8 x 80mm lengths of large down pipes
‚Ģ 4 x 80mm lengths of barge board strips
‚Ģ 2 x 80mm lengths of window sill strips
‚Ģ 8 down pipe hoppers
‚Ģ 8 wall tie plates
‚Ģ 4 soot/drainage manhole covers

A typical rural bus shelter to add interest to a village or small town scene. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 52mm x 35mm.

Pack contains 2 Bus Stops and Shelters plus stick on signs. See Modelscene Passengers Standing Sets A and B 5057 and 5058.

Pack contains 2 bus stops with shelters and 6 signs.

Pack contains 2 Cable Drums as supplied in the Modelscene 5078 Cable Laying Party.

Pack contains 2 pre-coloured Cable Drums

Pack contains 3 painted figures, Cable Drum and Wheelbarrow. Use Modelscene 5079 Cable Drums to extend this set.

Pack contains 3 painted figures and cable drum

Where carriages, multiple unit sets or modern locos are stored for cleaning and maintenance, narrow platforms are provided for access. Still widely used today alongside carriage sidings, and also within storage and maintenance facilities (See Ratio 527 Carriage Shed and Wills Modern SSM300 Modern Industrial Building and SSM315 Extension kits). Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint: 500mm long plus access steps

These were a common feature in sidings where repairs, cleaning and maintenance were effected. This shed will cover 2 tracks and can easily be extended; the kit includes guttering and centre walkway. A versatile kit with many uses both on and off the railway. Glue and paints required to complete model. Footprint 178mm x 60mm.

These were a common feature in sidings where repairs, cleaning and maintenance were effected. This shed will cover 2 tracks and can easily be extended; the kit includes guttering and centre walkway. A versatile kit with many uses both on and off the railway. Glue and paints required to complete model. Footprint 320mm x 105mm.