Enables an LGB(TM) motor to be fitted to a Peco G45 Turnout.

Locomotives and rolling stock are held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.

Pick up and other electrical problems solved; can be used with most plastics.

Allows the PL-50 Switch Module to be extended to any size required.

Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.

Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.

Abrasive rubber block for removing dirt and oxidisation from the rail surface. Improves running, particularly at low speeds.

Invaluable wiring aid - no soldering required. 2 strips of 12 blocks, easily cut with a craft knife into smaller units. Use them when extending wiring runs from Power Feed joiners (PL-80/81 and 82), Wiring Looms (PL-34) etc.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Keep your wiring organised and tidy with these self adhesive clips. Pack of 20 clips

Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.

Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary). Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip.

Open type, as used on the PL-15 Twin Microswitch. Rated 16v 2amps (continuous) or 2.5amps (momentary).

Push on Terminal Connectors and shrouds. These connectors make modification and fault finding so much easier than soldered wiring. Use them to connect the PL-38 Wire to PL-26 Passing Contact Switches, PL-22 On/Off Switches, PL-23 On/On Switches, and PL-34 Wiring Looms to PL-26 Passing Contact Switches. They can also be used when connecting wires to other items, for example, PL-13 Accessory Switches, PL-15 Twin Microswitches, PL-10 Turnout Motors, and PL-32 and 33 Microswitches.

These can be used directly from terminals on the Smartswitch (TM) Control Board (PLS-120) and Smartfrog (PLS-130) to show route selection. They can also be powered via a 12v DC supply if the PL-29 Resistors are included in the circuit.

Resistors for use with the PL-30 Red and Green LED's.

Use these when creating a diagrammatic control panel to clip fit PL-26 Passing Contact Switches, PL-22 On/Off Switches and PL-23 On/On Switches in the required place.

Houses 6 PL-26 Passing Contact Switches, PL-22 On/Off Switches or PL-23 On/On Switches.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

A useful remote operating feature for use with Peco N Gauge ELC couplings, or other N gauge couplings that do not incorporate a spring. 16 unobtrusive Coupling Lift Arms are supplied with this unit (NR-103 Coupling Lift Arms pack contains 32 if more are required). The uncoupler creates a temporary magnetic field which attracts the steel lift arm down, thereby pivoting the coupling upwards to decouple (at other times trains run through unaffected). A 16v AC supply is required, operated by a non latching push button (not included). Installation is simple, just drill a small hole in the centre of the trackbed and fit the unit under the baseboard with 2 screws. Full instructions included.

Allows adjacent switches in the PL-27 Switch Console and PL-50/51 Switch Module Unit to be ganged together and operated simultaneously.

Single Pole On/On Switch. Use this to switch power from one device to another or for operating items such as 2 aspect colour light signals.

Single Pole On/Off Switch. Use this to control features such as lighting circuits, or as a section switch where only 1 controller is used.

Clip this unit either side of an insulation gap on Peco H0/00 track. This can be used to isolate a loco at the end of a terminal road or siding, thereby enabling another loco to take the stock out. This is available as a ready made item in the Peco 00 Setrack range (ST-205/2005).

This plugs directly into a ready made recess on the 0 gauge Double Slip SL-E790BH to house a PL-33 Microswitch to operate the polarity switching.

A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.

A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.

This fits directly to the PL-10 family of Turnout Motors. The 2 single pole changeover switches can be used to control polarity, route selection diagrams, or 2 aspect colour light signalling etc. Rated 16v 2amps (continuous) or 2.5amps (momentary).

Attaches directly to the PL-10 family of Turnout Motors with contact adhesive. This single pole switch can control frog polarity, ground signals etc. PL-31 Spade Connectors can be used to attach wires to these units without the need for soldering.

2 Adaptor Bases are included, with optional extension arms, to enable PL-10 Turnout Motors to be mounted on the surface of the baseboard. This unit relies on the over centre spring in the turnout to keep the blades against the stock rail.

This unit enables a PL-10 Turnout Motor to be mounted on the surface of the baseboard, an optional extension arm is also included. A removable over centre spring is fitted, useful for turnouts which do not have this feature.

Clips directly into a Peco 00/H0 Setrack Turnout, either Left or Right Hand. No holes to drill, and this unit is pre wired. Can also be used with 00/H0 Streamline Turnouts.

The PL series of Turnout Motors is tried and tested, over the last 40 years we have sold literally millions of these motors. Simple, reliable and good value. An extended drive pin is fitted, use the PL-9 Mounting Plate to attach this unit to the underside of the baseboard. Attaching PL-13 and 15 Switches will enable switching for automatic polarity etc.

The PL series of Turnout Motors is tried and tested, over the last 40 years we have sold literally millions of these motors. Simple, reliable and good value. Requires a rectangular hole 40mm x 24mm when clipped directly to the underside of a Peco Turnout. Use the PL-12/12X if above baseboard mounting is required; attaching PL-13 and 15 Switches will enable switching for automatic polarity etc.

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects. (Pack of 4)

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects. (Pack of 8)

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects. (Pack of 7)

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects. (Pack of 6)

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects. (Pack of 6)

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects.(Pack of 6)

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects. (Pack of 6)