500 of these wagons (diagram O13) were built in 1913. Used for short run traffic in Cornwall and to carry china clay to potteries and paper mills. Final withdrawal took place in the late 1950s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

The GWR introduced a fleet of these vans (diagram Y4) in the early 1920s. These vans could still be seen in service into the 1950s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

10 ton Goods Van ‘Mink/Mink A’ V12, V14 and V16 Built between 1907 and 1927. Used for general goods traffic throughout the British railway system. In service until around 1960, later in departmental use. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

These gunpowder vans (diagram Z2) were built between 1913 and 1926 to carry gunpowder and other explosives. Examples lasted until around 1960. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

(Diagram O11/15) Over 12000 were built between 1909 and 1922. 011 had hand brake only and 015 wagons had the vacuum brake. Examples lasted into the 1950s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

7,000 of these vans were built between 1933 and 1945 for the carriage of general merchandise. Transfers are included; glue and paints are required to complete this model.

The term 'TOAD' refers to the GWR Telegraph Code for this type of vehicle. The kit includes 3 tail lamps, glazing, hand brake standard and transfers. Glue and paints are required to complete this model.

Built as part of the 'common user' pool of vehicles, their numbers totalled nearly 6,000. Made between 1931 and 1934, they were heavliy used all over the system. Transfers are included; glue and paints are required to complete this model.

‘Mica B’ X7 These vans were built in 1921 - 1923 to carry fresh or chilled meat. Some vans were converted to TEVANS in the 1930s. Most survived into Nationalisation in 1948 and a few into the early 1960s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers . Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

These wagons were used for carrying rail, girders, sawn timber, trees, telegraph poles, pipes etc. 'Steel girder' load included. Transfers are included; glue and paints are required to complete this model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Distant Signal. Kit includes pre-coloured signal arm, glue and paints required to complete model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Home Signal. Kit includes pre-coloured signal arm, glue and paints required to complete model.

Used first for perishable goods and later for gunpowder, these vans were also built by the LNWR, LSWR and used as private owner vans. Transfers are included; glue and paints are required to complete this model.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 36 posts and enough wire to make 720mm of fencing.

A simple kit to make this attractive half-cab Maudsley bus. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

A simple kit to make this attractive Thorneycroft vehicle. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

Built between 1933 and 1936 solely for the transport of cars. The end doors allowed cars to be driven in and out via a special unloading dock at the end of a siding. Transfers are included; glue and paints are required to complete this model.

Pack includes parts to make a pair of these heavy duty design bogies that feature cast steel type sideframes. Kit includes bolster, wheels and tension lock couplings; supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit contains 2 posts, 2 Home arms and 1 Distant. It can also be used with the Pratt Truss Gantry kit (Ref 478) to provide over track signals. Glue and paints required to complete model.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit enables you to replicate a GWR Junction/Bracket Home signal. Glue and paints required to complete model.

Advanced Construction Signals. Aimed at modellers with more experience, these kits enable you to custom make specific configurations of signals to suit your track layout and train paths. This kit will make either 4 separate signals, or combinations of bracket signals plus 4 Ground Signals. It can also be used with the Pratt Truss Gantry kit (Ref 478) to provide over track signals. Glue and paints required to complete model.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 680mm of fencing.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 340mm of Straight Fencing
‚Ģ 2 x 102mm lengths of Ramp Fencing
‚Ģ 1 Large and 1 Small Gate
‚Ģ 2 Ramp Gates
‚Ģ 1 Ticket Gate

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 680mm of fencing.

After loading, open wagons were checked for height using this simple gauge to ensure that loads did not hit bridges etc. and therefore were usually placed near the yard exit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Vacuum braked wagon underframe kit with steel type solebars. Kit and scratch builders' accessory; glue and paints are required to complete this model.

PECO Setrack 00 Gauge Code 100 - Unit trackage System
The high quality rigid unit trackage system suitable for all popular brands of 00 gauge model trains.
Being fully compatible with the Code 100 PECO Streamline range, it need never be discarded as your layout develops.
The solid nickel silver rails are integrally moulded into the sleeper bases for maximum realism and strength. Turnouts are fitted with an over-centre spring for immediate use, no extra levers necessary.

PECO Setrack 00 Gauge Code 100 - Unit trackage System
The high quality rigid unit trackage system suitable for all popular brands of 00 gauge model trains.
Being fully compatible with the Code 100 PECO Streamline range, it need never be discarded as your layout develops.
The solid nickel silver rails are integrally moulded into the sleeper bases for maximum realism and strength. Turnouts are fitted with an over-centre spring for immediate use, no extra levers necessary.

A simple kit to make this attractive Throneycroft vehicle. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

Keep on the right side of health and safety regulations - use these double rail stanchions in locations wherever the general public are allowed. Pack contains 20 injection moulded supports and approx 2 x 400mm length of nickel silver railing.

Always difficult to scratchbuild, these realistic features will enhance any industrial installation that needs a single rail safety barrier. Pack contains 20 injection moulded supports and 400mm length of brass wire.

A string of nets, boxes and creels.
Size approx (mm) L90 x W25 x H12 The Harburn Hamlet range of painted resin accessories provide interesting scenic details to go around the quayside on your layout.

Pack of 5. Size each approx (mm) L17 x W10 x H6. The Harburn Hamlet range of painted resin accessories provide interesting scenic details for your layout.

Typical American style buffer with central buffing plate, clips between the rails.

Pack contains 8 pieces

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Enables you to change the SSM300 into a Distribution Depot. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Pack of 2. Use with the SS300 Straight Brick walls to produce a boundary wall.
Size (mm) 65 x 11 x 30 and 58 x 11 x 30. The Harburn Hamlet range of painted resin accessories provide interesting scenic details to go around the station and streets of your layout.

Pack of 2. Use with the SS300 Straight Brick walls to produce a boundary wall.
Size (mm) 80 x 46 x 30. The Harburn Hamlet range of painted resin accessories provide interesting scenic details to go around the station and streets of your layout.

Pack of 2 90¬? degree curved walls. Use with the SS300 Straight Brick walls to produce a boundary wall. A difficult modelling task made easy, curved wall incorporating buttresses.
Size (mm) 100 x 35 x 22. The Harburn Hamlet range of painted resin accessories provide interesting scenic details to go around the station and streets of your layout.

Pack of 2. Substantial traditional brick walling for perimeters of loco depots, schools, factories, etc. See SS301 and 2 to add corners, and SS303 for gate entrances.
Size each (mm) 102.5 x 11 x 22The Harburn Hamlet range of painted resin accessories provide interesting scenic details to go around the station and streets of your layout.

Pack contains 5 fully painted hiking figures.

Kit includes 2 large hoardings plus 3 smaller ones, Bill Stickers himself plus ladder and paste bucket, plus a sheet of 40 posters. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 58mm x 32mm each.

Pack contains 2 Hoardings plus a selection of signs

Pack contains 2 Hoardings plus a selection of signs

Used for light lifting work in goods depots and other yards. Also to be found inside goods sheds for unloading wagons. Chain included; kit requires glue and paints to complete.

For Hornby (TM) wagons with internal measurements as shown.
Size (mm) 62 x 28. The Harburn Hamlet range of painted resin accessories provide interesting scenic details for your layout.