All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Usually supplied by a water tower (See LK-1, Ratio 506, 540, 551 and Wills SS34 kits).

Stations often had these Water Cranes at the end of the platforms so the locomotives could be refilled without detaching them from the train. Also included is a coke brazier, called a 'fire devil' to keep the cast iron pipe from freezing up during the winter. These cranes were usually supplied by a large water tank (see Ratio Water Tower kits 215, 256 and Loco Servicing Depot kit 206). Supplied with some pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Stations often had these Water Cranes at the end of the platforms so the locomotives could be refilled without detaching them from the train. Also included is a coke brazier, called a 'fire devil' to keep the cast iron pipe from freezing up during the winter. These cranes were usually supplied by a large water tank (see Ratio 506 and 551 and Wills SS34 kits). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

10 6mm high self adhesive Water Meadow Grass tuft strips, each approximately 130mm long, to stick down wherever required on your layout or diorama.

Supplied in a square-section tube, the three separate sheets will match perfectly together to form a continuous run of 2400mm (95in), and reaching to a height of 333mm (13in). Future backscenes will match at either end allowing longer runs of scenery throughout the full length of a layout.

Often seen in the loco yard or near the platform end. Use LK-2 Water Cranes if additional cranes are required.

A raised water supply for an engine shed or to supply platform water cranes (See Ratio 413 and Peco LK-2 Water Cranes, also Ratio 550 Water Troughs). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 66mm x 55mm.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 370mm of troughs and includes relevant signboards. Use in conjunction with the Large Water Tower (Ref 256). Glue and paints are required to complete this model.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 760mm of troughs and includes relevant signboards. Use in conjunction with the large Water Tower (Ref 551). Glue and paints are required to complete this model.

Enables you to make a building into a water mill. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Pack includes 10 pieces

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint; Weighing Deck 85mm x 50mm, hut 45mm x 35mm.

Commercial vehicles arriving with goods to transport by rail were weighed to work out their levy. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 82mm x 81mm

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Kit includes guttering, brass etched scales and weighing plate, barge boards, window and door; glue and paints required to complete this model. Footprint: 30mm x 15mm.

Pack of 4, 2 different types.

A simple kit to make this attractive half-cab Maudsley bus. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

10 4mm high self adhesive wild meadow tuft strips, each approximately 130mm long, to stick down wherever required on your layout or diorama.

10 6mm high self adhesive Wild Meadow Grass tuft strips, each approximately 130mm long, to stick down wherever required on your layout or diorama.

Scratch and Kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 3 assorted domestic doors plus optional assorted door surrounds
‚Ģ 12 assorted domestic window frames plus optional assorted window surrounds

Useful detail components for scratchbuilders.

Scratch and kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 5 assorted doors
‚Ģ Pentice roof and supports (to go over a door)
‚Ģ 2 Domestic gatess
‚Ģ 15 assorted domestic windows
‚Ģ 7 assorted decorative window lintels

10 6mm high self adhesive Winter Grass tuft strips, each approximately 130mm long, to stick down wherever required on your layout or diorama.