A raised water supply for an engine shed or to supply platform water cranes (See Ratio 413 and Peco LK-2 Water Cranes, also Ratio 550 Water Troughs). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 66mm x 55mm.

A fairly universal design seen at many steam loco depots. The kit includes water gauge, water crane, fire buckets and lamp. Use the Ratio 413 Water Crane and Fire Devil kit if further cranes are required. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 90mm x 60mm

Stations often had these Water Cranes at the end of the platforms so the locomotives could be refilled without detaching them from the train. Also included is a coke brazier, called a 'fire devil' to keep the cast iron pipe from freezing up during the winter. These cranes were usually supplied by a large water tank (see Ratio 506 and 551 and Wills SS34 kits). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Add interest to your village centre with these generic structures. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. footprint: 76mm x 59mm.

A building to complement the SSAM101 Blacksmith Set. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 84mm x 55mm.

This type of urinal, consisting of cast iron screens but otherwise open to the elements was found at busy locations in city centres and railway stations. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 92mm x 34mm.

Model of a Victorian style cast iron bridge, designed to be used with the SS64 abutments kit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Span: 110mm

This Plate Girder Bridge kit can be made up to suit the length of span required, and is therefore particularly useful where roads/ railways cross at an angle other than 90 degrees or where a long bridge is required. Maximum girder length 352mm. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

From the late 1960's the spread of shipping containers revolutionised the transport of goods. On the railways marshalling yards gave way to intermodal depots as containers are transferred between ships, trains and road vehicles. The Rolling Underframe kit (Ref 546A) can be added to transform this unit into a movable crane. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint; Sides 61mm wide X 125mm High, Span 153mm

Timber yards and Builders merchants premises offer possibilities of extra variety of traffic into the station goods yard. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Based on the Saxby and Farmer design seen on many railways across Britain. Footprint: 90mm x 56mm + 40mm over staircase. The Ratio Signal Box Interior kit 553 will provide a wealth of interior detail. Don't forget SS89 Point Rodding, SS22 Lamp Huts and, of course, signals! Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

This Island Platform building is designed to be used with the Wills SS61 Platform and SS54 Canopy, and can easily be adapted to make a larger building using additional kits.Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 92mm x 60mm.