SORT BY
PAGE

1824 Products Found

Red Connecting Wire

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Green Connecting Wire

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Black Connecting Wire

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Blue Connecting Wire

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Cable Clips (Pack of 20)

Keep your wiring organised and tidy with these self adhesive clips. Pack of 20 clips

Wiring Harness for PL-10 Series Turnout Motors

Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.

Closed Microswitch

Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary). Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip.

Open Microswitch

Open type, as used on the PL-15 Twin Microswitch. Rated 16v 2amps (continuous) or 2.5amps (momentary).

LED's

These can be used directly from terminals on the Smartswitch (TM) Control Board (PLS-120) and Smartfrog (PLS-130) to show route selection. They can also be powered via a 12v DC supply if the PL-29 Resistors are included in the circuit.

Terminal Connectors/Shrouds

Push on Terminal Connectors and shrouds. These connectors make modification and fault finding so much easier than soldered wiring. Use them to connect the PL-38 Wire to PL-26 Passing Contact Switches, PL-22 On/Off Switches, PL-23 On/On Switches, and PL-34 Wiring Looms to PL-26 Passing Contact Switches. They can also be used when connecting wires to other items, for example, PL-13 Accessory Switches, PL-15 Twin Microswitches, PL-10 Turnout Motors, and PL-32 and 33 Microswitches.

Switch Console

Houses 6 PL-26 Passing Contact Switches, PL-22 On/Off Switches or PL-23 On/On Switches.

Resistors for LED's

Resistors for use with the PL-30 Red and Green LED's.

Switch Mounting Plate

Use these when creating a diagrammatic control panel to clip fit PL-26 Passing Contact Switches, PL-22 On/Off Switches and PL-23 On/On Switches in the required place.

Yellow Passing Contact Switch

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

White Passing Contact Switch

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Red Passing Contact Switch

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Black Passing Contact Switch

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Decoupler Electro Magnetic Unit

A useful remote operating feature for use with Peco N Gauge ELC couplings, or other N gauge couplings that do not incorporate a spring. 16 unobtrusive Coupling Lift Arms are supplied with this unit (NR-103 Coupling Lift Arms pack contains 32 if more are required). The uncoupler creates a temporary magnetic field which attracts the steel lift arm down, thereby pivoting the coupling upwards to decouple (at other times trains run through unaffected). A 16v AC supply is required, operated by a non latching push button (not included). Installation is simple, just drill a small hole in the centre of the trackbed and fit the unit under the baseboard with 2 screws. Full instructions included.

Switch Joining Bars

Allows adjacent switches in the PL-27 Switch Console and PL-50/51 Switch Module Unit to be ganged together and operated simultaneously.

Single Pole Changeover Switch (On/On)

Single Pole On/On Switch. Use this to switch power from one device to another or for operating items such as 2 aspect colour light signals.

On/Off Switch

Single Pole On/Off Switch. Use this to control features such as lighting circuits, or as a section switch where only 1 controller is used.

Microswitch Housing

This plugs directly into a ready made recess on the 0 gauge Double Slip SL-E790BH to house a PL-33 Microswitch to operate the polarity switching.

Stud and Tag Washers for Turnout Motor operation

A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.

Track Isolating Switch

Clip this unit either side of an insulation gap on Peco H0/00 track. This can be used to isolate a loco at the end of a terminal road or siding, thereby enabling another loco to take the stock out. This is available as a ready made item in the Peco 00 Setrack range (ST-205/2005).

PAGE

Trade Login

WOULD YOU LIKE TO BECOME A TRADE PARTNER?

PECO - PLEASE SUPPLY TEXT.
An introductory paragraph with criteria listed as bullets points, closing with contact call to action.