The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Control Board will facilitate the control of up to 4 Servos. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.

Base unit for use with the PL-10E Turnout Motor. Fixing screws and full instructions included.

Enables an LGB(TM) motor to be fitted to a Peco G45 Turnout.

Pick up and other electrical problems solved; can be used with most plastics.

Look after your model collection with this extremely useful kit, one handy pack has the things you need for basic cleaning and lubrication. The Kit contains Power Lube, Wheel Cleaning Brush and Scraper and the Locomotive Servicing Cradle which enables locomotives and rolling stock to be held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.

Locomotives and rolling stock are held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.

Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.

Allows the PL-50 Switch Module to be extended to any size required.

Enables switches to be connected without any need for soldering. Power is supplied through the fitted leads and each switch is automatically connected when fitted. Simply push the button on the front to open the holes, and feed in the bare wires from the turnout motor - no soldering or other fixing required. The PL-51 allows the PL-50 module to be extended to any size required.

Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.

Invaluable wiring aid - no soldering required. 2 strips of 12 blocks, easily cut with a craft knife into smaller units. Use them when extending wiring runs from Power Feed joiners (PL-80/81 and 82), Wiring Looms (PL-34) etc.

Abrasive rubber block for removing dirt and oxidisation from the rail surface. Improves running, particularly at low speeds.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Keep your wiring organised and tidy with these self adhesive clips. Pack of 20 clips

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.

Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary). Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip.

For use with all solenoid motors (e.g. PL-10 and Pl-11). Connect this unit to the 16v ac supply on your transformer. The capacitor stores up power and discharges a 'kick' to ensure turnout blades 'snap over' every time.

Push on Terminal Connectors and shrouds. These connectors make modification and fault finding so much easier than soldered wiring. Use them to connect the PL-38 Wire to PL-26 Passing Contact Switches, PL-22 On/Off Switches, PL-23 On/On Switches, and PL-34 Wiring Looms to PL-26 Passing Contact Switches. They can also be used when connecting wires to other items, for example, PL-13 Accessory Switches, PL-15 Twin Microswitches, PL-10 Turnout Motors, and PL-32 and 33 Microswitches.

Open type, as used on the PL-15 Twin Microswitch. Rated 16v 2amps (continuous) or 2.5amps (momentary).

These can be used directly from terminals on the Smartswitch (TM) Control Board (PLS-120) and Smartfrog (PLS-130) to show route selection. They can also be powered via a 12v DC supply if the PL-29 Resistors are included in the circuit.