The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Abrasive rubber block for removing dirt and oxidisation from the rail surface. Improves running, particularly at low speeds.

A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.

Pick up and other electrical problems solved; can be used with most plastics.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

204mm track feed wires ready soldered to rail joiners. Quick and easy to use, avoids the risk of damage to sleepers from soldering irons. Easily extended using PL-39 Terminal Blocks and PL-38 Red and Black wire. 4 pairs per pack.

Open type, as used on the PL-15 Twin Microswitch. Rated 16v 2amps (continuous) or 2.5amps (momentary).

Single Pole On/Off Switch. Use this to control features such as lighting circuits, or as a section switch where only 1 controller is used.

Base unit for use with the PL-10E Turnout Motor. Fixing screws and full instructions included.

This plugs directly into a ready made recess on the 0 gauge Double Slip SL-E790BH to house a PL-33 Microswitch to operate the polarity switching.

Locomotives and rolling stock are held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.

These can be used directly from terminals on the Smartswitch (TM) Control Board (PLS-120) and Smartfrog (PLS-130) to show route selection. They can also be powered via a 12v DC supply if the PL-29 Resistors are included in the circuit.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary). Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
‚Ģ An additional Mast plus push on/push off hangar to extend the LC-100 Catenary System Startup Pack.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available.
‚Ģ The Installation jig is for use when installing the OHLE Catenary system. N.B. 2 of these jigs are included in the LC-100 Catenary System Startup Pack.

Keep your wiring organised and tidy with these self adhesive clips. Pack of 20 clips

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Attaches directly to the PL-10 family of Turnout Motors with contact adhesive. This single pole switch can control frog polarity, ground signals etc. PL-31 Spade Connectors can be used to attach wires to these units without the need for soldering.

The Peco Catenary System enables 00 Gauge modellers to faithfully replicate the BR Mk.3 System widely used around the country. The system features all metal construction with steel posts and copper contact wires with comprehensive instructions and installation jigs available. This pack includes:
‚Ģ 5 200mm long OHLE Contact Wires for use with the LC-100 Catenary System 12 Mast Pack and LC-110 Catenary System Mast.