Footprints: Greenhouse 56mm x 41mm, Cold Frames 26mm x 25mm each (glazing included). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

2 huts and a privy as seen on allotments everywhere. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Combined footprint: 94mm x 38mm

A small signal box as would be seen at a small country station, or controlling the exit from a yard or industrial area. Use SS89 Point Rodding to fill in this important detail on your layout. Footprint:48mm x 36mm.

Makes 4 Ground Signals, glue and paints required to complete model.

The use of old coach bodies as stores, mess huts or even homes was common. Clutter included, huge scope for adding detail to such a scene. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 115mm x 40mm

Usually used for storage around the station or goods yard, they often can be found being used as sheds or on farmland. Clutter included; supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint 176mm x 90mm

Pack includes: 432mm of guttering, 465mm of soffits, 4 x 71mm down pipes, 1 angled water pipe and 14 down pipe brackets.

500 of these wagons (diagram O13) were built in 1913. Used for short run traffic in Cornwall and to carry china clay to potteries and paper mills. Final withdrawal took place in the late 1950s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

The GWR introduced a fleet of these vans (diagram Y4) in the early 1920s. These vans could still be seen in service into the 1950s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

10 ton Goods Van ‘Mink/Mink A’ V12, V14 and V16 Built between 1907 and 1927. Used for general goods traffic throughout the British railway system. In service until around 1960, later in departmental use. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

These gunpowder vans (diagram Z2) were built between 1913 and 1926 to carry gunpowder and other explosives. Examples lasted until around 1960. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

(Diagram O11/15) Over 12000 were built between 1909 and 1922. 011 had hand brake only and 015 wagons had the vacuum brake. Examples lasted into the 1950s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

7,000 of these vans were built between 1933 and 1945 for the carriage of general merchandise. Transfers are included; glue and paints are required to complete this model.

The term 'TOAD' refers to the GWR Telegraph Code for this type of vehicle. The kit includes 3 tail lamps, glazing, hand brake standard and transfers. Glue and paints are required to complete this model.

Built as part of the 'common user' pool of vehicles, their numbers totalled nearly 6,000. Made between 1931 and 1934, they were heavliy used all over the system. Transfers are included; glue and paints are required to complete this model.

‘Mica B’ X7 These vans were built in 1921 - 1923 to carry fresh or chilled meat. Some vans were converted to TEVANS in the 1930s. Most survived into Nationalisation in 1948 and a few into the early 1960s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings. Glue and paint will be required, along with appropriate transfers . Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

These wagons were used for carrying rail, girders, sawn timber, trees, telegraph poles, pipes etc. 'Steel girder' load included. Transfers are included; glue and paints are required to complete this model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Distant Signal. Kit includes pre-coloured signal arm, glue and paints required to complete model.

Part of the Ratio 'Quick Assembly' family of signals. These allow you to make home and distant signals quickly and easily. They include signal operating wire and lever. This kit enables you to replicate a GWR Home Signal. Kit includes pre-coloured signal arm, glue and paints required to complete model.

Used first for perishable goods and later for gunpowder, these vans were also built by the LNWR, LSWR and used as private owner vans. Transfers are included; glue and paints are required to complete this model.

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains 36 posts and enough wire to make 720mm of fencing.

A simple kit to make this attractive half-cab Maudsley bus. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

A simple kit to make this attractive Thorneycroft vehicle. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

Built between 1933 and 1936 solely for the transport of cars. The end doors allowed cars to be driven in and out via a special unloading dock at the end of a siding. Transfers are included; glue and paints are required to complete this model.