PECO Setrack 00 Gauge Code 100 - Unit trackage System
The high quality rigid unit trackage system suitable for all popular brands of 00 gauge model trains.
Being fully compatible with the Code 100 PECO Streamline range, it need never be discarded as your layout develops.
The solid nickel silver rails are integrally moulded into the sleeper bases for maximum realism and strength. Turnouts are fitted with an over-centre spring for immediate use, no extra levers necessary. 2nd Radius Left Hand Turnout.

PECO Setrack 00 Gauge Code 100 - Unit trackage System
The high quality rigid unit trackage system suitable for all popular brands of 00 gauge model trains.
Being fully compatible with the Code 100 PECO Streamline range, it need never be discarded as your layout develops.
The solid nickel silver rails are integrally moulded into the sleeper bases for maximum realism and strength. Turnouts are fitted with an over-centre spring for immediate use, no extra levers necessary. 2nd Radius Left Hand Turnout.

Private owner wagons abounded prior to nationalisation, they would often be seen far from their base as they were sent to collect raw materials and supplies such as coal, and deliver finished goods. All Peco wagons feature free running wheels in pin point axles. The ELC coupling, whilst compatible with the standard N gauge couplings, keeps a realistic distance between vehicles and enables the PL-25 electro magnetic decoupler to be used for remote uncoupling.

Pack contains 15 unpainted figures. A cost effective way of populating your layout or diorama, these figures come attached to sprues to make handling easier when painting.

Pack contains 14 unpainted figures. A cost effective way of populating your layout or diorama, these figures come attached to sprues to make handling easier when painting.

Pack contains 20 unpainted figures. A cost effective way of populating your layout or diorama, these figures come attached to sprues to make handling easier when painting.

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient parts to 'convert' one wagon to a vacuum braked vehicle; it contains Dean/Churchward short brake lever, brackets and rodding, vacuum pipes and cylinder, plus steam pipes.

This Plate Girder Bridge kit can be made up to suit the length of span required, and is therefore particularly useful where roads/ railways cross at an angle other than 90 degrees or where a long bridge is required. Maximum girder length 352mm. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Air brake, no headstocks as supplied with VEA ex Vanwide kit PC76.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Model of a Victorian style cast iron bridge, designed to be used with the SS64 abutments kit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Span: 110mm

This type of urinal, consisting of cast iron screens but otherwise open to the elements was found at busy locations in city centres and railway stations. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 92mm x 34mm.

A building to complement the SSAM101 Blacksmith Set. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 84mm x 55mm.

Add interest to your village centre with these generic structures. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. footprint: 76mm x 59mm.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

Pack of 3 for Lima/Dapol (TM) wagons.

Pack of 3 for Hornby (TM) wagons.

Pack of 3 for Lima/Dapol (TM) wagons.

Pack of 3 for Hornby (TM) wagons.

Pack of 3 for Lima/Dapol (TM) wagons.

Pack of 3 for Hornby (TM) wagons.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Usually supplied by a water tower (See LK-1, Ratio 506, 540, 551 and Wills SS34 kits).

Stations often had these Water Cranes at the end of the platforms so the locomotives could be refilled without detaching them from the train. Also included is a coke brazier, called a 'fire devil' to keep the cast iron pipe from freezing up during the winter. These cranes were usually supplied by a large water tank (see Ratio Water Tower kits 215, 256 and Loco Servicing Depot kit 206). Supplied with some pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Stations often had these Water Cranes at the end of the platforms so the locomotives could be refilled without detaching them from the train. Also included is a coke brazier, called a 'fire devil' to keep the cast iron pipe from freezing up during the winter. These cranes were usually supplied by a large water tank (see Ratio 506 and 551 and Wills SS34 kits). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Often seen in the loco yard or near the platform end. Use LK-2 Water Cranes if additional cranes are required.

A raised water supply for an engine shed or to supply platform water cranes (See Ratio 413 and Peco LK-2 Water Cranes, also Ratio 550 Water Troughs). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 66mm x 55mm.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 370mm of troughs and includes relevant signboards. Use in conjunction with the Large Water Tower (Ref 256). Glue and paints are required to complete this model.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 760mm of troughs and includes relevant signboards. Use in conjunction with the large Water Tower (Ref 551). Glue and paints are required to complete this model.

Enables you to make a building into a water mill. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Pack includes 10 pieces

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint; Weighing Deck 85mm x 50mm, hut 45mm x 35mm.

Commercial vehicles arriving with goods to transport by rail were weighed to work out their levy. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 82mm x 81mm

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Kit includes guttering, brass etched scales and weighing plate, barge boards, window and door; glue and paints required to complete this model. Footprint: 30mm x 15mm.

Pack of 4, 2 different types.

A simple kit to make this attractive half-cab Maudsley bus. Kit contains pre-coloured parts and transfers. Requires glue and detail painting to complete.

Private owner wagons abounded prior to nationalisation, they would often be seen far from their base as they were sent to collect raw materials and supplies such as coal, and deliver finished goods. All Peco wagons feature free running wheels in pin point axles. The ELC coupling, whilst compatible with the standard N gauge couplings, keeps a realistic distance between vehicles and enables the PL-25 electro magnetic decoupler to be used for remote uncoupling.

Scratch and Kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 3 assorted domestic doors plus optional assorted door surrounds
‚Ģ 12 assorted domestic window frames plus optional assorted window surrounds

Useful detail components for scratchbuilders.

Scratch and kit builders accessory pack. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This kit includes:
‚Ģ 5 assorted doors
‚Ģ Pentice roof and supports (to go over a door)
‚Ģ 2 Domestic gatess
‚Ģ 15 assorted domestic windows
‚Ģ 7 assorted decorative window lintels

Peco Setrack Bullhead 0 Gauge track makes it possible have somewhere to run trains without having to build or find room for a fixed layout. With Setrack you can lay out your trackwork indoors on the floor or out on the patio in any configuration you choose and pack it away again afterwards. Compatible with and made to the same high standard of detail and realism as the Bullhead Streamline range, it can also be incorporated into a Streamline layout without problems. Made with solid nickel silver rail to the classic bullhead section and check rail are also machined from solid rail. The SL-713 0 Gauge Bullhead to Flat Bottom Transition Track makes it easy to also incorporate the Setrack range into a layout using Flat Bottom track.

20 175mm lengths of wood grain effect sleepering for track and turnout construction.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm