6 Telegraph Poles, these also carried railway bell codes and phone connections between signal boxes and stations as well as GPO lines.

Kit for the iconic telephone box.

Pack contains a simple 4 piece kit to make a Telephone Box plus a painted caller.

Pack contains simple 4 piece kits to make 2 Telephone Boxes

Pack contains 3 pre-coloured Telephone Boxes.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Supplied in a square-section tube, the three separate sheets will match perfectly together to form a continuous run of 2400mm (95in), and reaching to a height of 333mm (13in).

Kit to produce dirty track bed on your ballasted track areas to represent weathering, dirt and oily grime between the rails at stations, at points, signal areas and engine maintenance depots. This kit is specially designed for layouts using diesel locomotives.

Kit to produce dirty track bed on your ballasted track areas to represent weathering, dirt and oily grime between the rails at stations, at points, signal areas and engine maintenance depots. This kit is specially designed for layouts using steam locomotives.

Fully painted figures to depict a permanent way team. See Modelscene 5002 Ballast Bins; Lineside Hut Kits Ratio Ref. 511 and 518, also Wills Ref. SS50.

Pack contains 3 Track Signs

Pack contains 20 assorted Traffic Cones

Pack contains 5 signs with stick on notices.

Pack contains 4 Trunks, 6 Suitcases, and 2 Sack Trucks to add detail to your station platform.

Can be used with Wills SS83 Stone Piers to create an impressive viaduct as seen on many railways around the world. Detailed plastic moulding supplied 2 in a pack.

Pair of detailed Tunnel Mouths, with separate wings walls for optional positioning. Matching Stone Walling is also available (NB-40).

Pair of detailed Tunnel Mouths, with separate wings walls for optional positioning. Matching Stone Walling is also available (NB-40).

A sturdy, pre coloured Tunnel Mouth that is easy to integrate into your hillside

A sturdy, pre coloured Tunnel Mouth that is easy to integrate into your hillside

For narrow gauge models built to either 00 (4mm) or H0 (3.5mm) scale and running on 9mm gauge track, this range depicts the slightly worn out old track of a picturesque old railway. It is fully compatible with the Peco 009 Setrack rigid track system. This cosmetic turnout lever will add realism to your station yards and sidings.

Pack contains 15 unpainted figures. A cost effective way of populating your layout or diorama, these figures come attached to sprues to make handling easier when painting.

Pack contains 14 unpainted figures. A cost effective way of populating your layout or diorama, these figures come attached to sprues to make handling easier when painting.

Pack contains 20 unpainted figures. A cost effective way of populating your layout or diorama, these figures come attached to sprues to make handling easier when painting.

This Plate Girder Bridge kit can be made up to suit the length of span required, and is therefore particularly useful where roads/ railways cross at an angle other than 90 degrees or where a long bridge is required. Maximum girder length 352mm. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Model of a Victorian style cast iron bridge, designed to be used with the SS64 abutments kit. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Span: 110mm

This type of urinal, consisting of cast iron screens but otherwise open to the elements was found at busy locations in city centres and railway stations. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 92mm x 34mm.

A building to complement the SSAM101 Blacksmith Set. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 84mm x 55mm.

Add interest to your village centre with these generic structures. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. footprint: 76mm x 59mm.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

All kits comprise a bag of load material, such as coal or sand, plus sections of board that are cut to size to fit the desired wagon. The modeller, using a PVA adhesive, secures the materials on the cut boards and places the load inside the wagon for instant effect. The additional benefit, apart from the realism, is that some valuable weight is added to what might otherwise be a very light vehicle. Especially useful in an N scale wagon!

The N scale kits contain enough material for up to 6 wagons. Full instructions are provided in the packs.

These sheets are invaluable for scratchbuilding, saving many hours of repetitive work creating the various surface patterns and textures. They are the same as those used in the Craftsman kits to make extension work easier. Each pack contains 4 sheets 130mm x 75mm of injection moulded styrene approximately 2mm thick, making them rigid enough to be self supporting.

Usually supplied by a water tower (See LK-1, Ratio 506, 540, 551 and Wills SS34 kits).

Stations often had these Water Cranes at the end of the platforms so the locomotives could be refilled without detaching them from the train. Also included is a coke brazier, called a 'fire devil' to keep the cast iron pipe from freezing up during the winter. These cranes were usually supplied by a large water tank (see Ratio Water Tower kits 215, 256 and Loco Servicing Depot kit 206). Supplied with some pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Stations often had these Water Cranes at the end of the platforms so the locomotives could be refilled without detaching them from the train. Also included is a coke brazier, called a 'fire devil' to keep the cast iron pipe from freezing up during the winter. These cranes were usually supplied by a large water tank (see Ratio 506 and 551 and Wills SS34 kits). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

10 6mm high self adhesive Water Meadow Grass tuft strips, each approximately 130mm long, to stick down wherever required on your layout or diorama.

Supplied in a square-section tube, the three separate sheets will match perfectly together to form a continuous run of 2400mm (95in), and reaching to a height of 333mm (13in). Future backscenes will match at either end allowing longer runs of scenery throughout the full length of a layout.

Often seen in the loco yard or near the platform end. Use LK-2 Water Cranes if additional cranes are required.

A raised water supply for an engine shed or to supply platform water cranes (See Ratio 413 and Peco LK-2 Water Cranes, also Ratio 550 Water Troughs). Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. Footprint: 66mm x 55mm.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 370mm of troughs and includes relevant signboards. Use in conjunction with the Large Water Tower (Ref 256). Glue and paints are required to complete this model.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 760mm of troughs and includes relevant signboards. Use in conjunction with the large Water Tower (Ref 551). Glue and paints are required to complete this model.

Enables you to make a building into a water mill. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Pack includes 10 pieces