Our natural materials are ideal for producing realistic ballast, scenery and wagon loads etc.

Our natural materials are ideal for producing realistic ballast, scenery and wagon loads etc.

Our natural materials are ideal for producing realistic ballast, scenery and wagon loads etc.

Pack of 10, suitable for 1/160 scale MGR Hopper wagons.

Our natural materials are ideal for producing realistic ballast, scenery and wagon loads etc.

Introduced in 1928 (diagram 1771), and still in service carrying a wide variety of Civil Engineer’s materials on BR Southern Region. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

Pack of 20; kit and scratch builders accessory.

Pack of 20; kit and scratch builders accessory.

Introduced in 1949 (diagram 1/462), and intended to carry cast iron pipes, but were also used widely for other loads. Examples survived into the 1980s. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

From 1936, these wagons (diagram 1974) carried coal to the company’s loco depots. Used by for general coal traffic until the late 1960s. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

Introduced in 1924, and part of GWR’s drive to use higher capacity wagons. Known as ‘Pole’ wagons (diagram N24) after the company’s General Manager. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

A standard 1930s design, they carried coal to the company’s loco depots. Used by BR for general coal traffic. Withdrawn around 1960. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

Kit and scratch builder's accessory. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

Over 2000 of these wagons were built to carry coal to large concerns such as power stations and steel works. Period 1953-1982. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

Over 4000 of these wagons were built to carry sleepers and ballast for track maintenance. Period 1951 to present. These finely moulded plastic wagon kits come complete with pin point axle wheels. Glue and paint will be required, along with appropriate transfers .

From choosing a suitable location for your 00 Gauge layout, and the type of control methods to use, this book is packed with advise and inspiration for new railway modellers and returnees to the hobby alike. There is also a look back at the history of 00 gauge, and a wealth of practical projects, many of which will be simple evenings' tasks that will enhance your models and hone new skills. Additionally, maintenance advice is given to keep your layout in tip top condition, plus a selection of track plans to help you get started. 122 pages fully illustrated.

All PECO Publications now available as digital downloads on tablets and mobile devices through their respective App Stores. Download on the App Store or get it on Google Play.

An inspirational 122 page book looking at the railways of Europe, includes some first class modelling of interesting places; also ideas for modelling and construction techniques.

All PECO Publications now available as digital downloads on tablets and mobile devices through their respective App Stores. Download on the App Store or get it on Google Play.

As well as the starting point for most model railway projects, trackplans are a fascinating aspect of the hobby in their own right. For many years they have been a popular feature in Railway Modeller magazine and are presented here for the first time in one handy volume. 64 pages fully illustrated.

All PECO Publications now available as digital downloads on tablets and mobile devices through their respective App Stores. Download on the App Store or get it on Google Play.

The sheer variety of railroads in North America makes them a subject with enormous potential for enthusiasts everywhere. This invaluable guide is aimed at everyone who wishes to start modelling or enjoys this perennially fascinating subject. 130 pages fully illustrated.

All PECO Publications now available as digital downloads on tablets and mobile devices through their respective App Stores. Download on the App Store or get it on Google Play.

The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Extension cable allows a servo to be located up to a metre further away from the Control Board. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.

Enables an LGB(TM) motor to be fitted to a Peco G45 Turnout.

Base unit for use with the PL-10E Turnout Motor. Fixing screws and full instructions included.

Locomotives and rolling stock are held safely during servicing, leaving both hands free. Suitable for 00/H0, N, and many narrow gauge locos.

Pick up and other electrical problems solved; can be used with most plastics.

Allows the PL-50 Switch Module to be extended to any size required.

Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.

Simply connect the wires from the brush and scraper directly to your layout power supply and apply them to the driving wheels, one on each side.

Abrasive rubber block for removing dirt and oxidisation from the rail surface. Improves running, particularly at low speeds.

Invaluable wiring aid - no soldering required. 2 strips of 12 blocks, easily cut with a craft knife into smaller units. Use them when extending wiring runs from Power Feed joiners (PL-80/81 and 82), Wiring Looms (PL-34) etc.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

The vital link. Your model railway will be so much easier to extend and maintain if you adopt a colour code scheme for the wiring.

Keep your wiring organised and tidy with these self adhesive clips. Pack of 20 clips

Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.

Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary). Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip.

Open type, as used on the PL-15 Twin Microswitch. Rated 16v 2amps (continuous) or 2.5amps (momentary).

These can be used directly from terminals on the Smartswitch (TM) Control Board (PLS-120) and Smartfrog (PLS-130) to show route selection. They can also be powered via a 12v DC supply if the PL-29 Resistors are included in the circuit.

Push on Terminal Connectors and shrouds. These connectors make modification and fault finding so much easier than soldered wiring. Use them to connect the PL-38 Wire to PL-26 Passing Contact Switches, PL-22 On/Off Switches, PL-23 On/On Switches, and PL-34 Wiring Looms to PL-26 Passing Contact Switches. They can also be used when connecting wires to other items, for example, PL-13 Accessory Switches, PL-15 Twin Microswitches, PL-10 Turnout Motors, and PL-32 and 33 Microswitches.

Houses 6 PL-26 Passing Contact Switches, PL-22 On/Off Switches or PL-23 On/On Switches.

Resistors for use with the PL-30 Red and Green LED's.

Use these when creating a diagrammatic control panel to clip fit PL-26 Passing Contact Switches, PL-22 On/Off Switches and PL-23 On/On Switches in the required place.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.

A useful remote operating feature for use with Peco N Gauge ELC couplings, or other N gauge couplings that do not incorporate a spring. 16 unobtrusive Coupling Lift Arms are supplied with this unit (NR-103 Coupling Lift Arms pack contains 32 if more are required). The uncoupler creates a temporary magnetic field which attracts the steel lift arm down, thereby pivoting the coupling upwards to decouple (at other times trains run through unaffected). A 16v AC supply is required, operated by a non latching push button (not included). Installation is simple, just drill a small hole in the centre of the trackbed and fit the unit under the baseboard with 2 screws. Full instructions included.