A essential feature on steam era main lines for over 100 years; this kit contains parts to make 760mm of troughs and includes relevant signboards. Use in conjunction with the large Water Tower (Ref 551). Glue and paints are required to complete this model.

A essential feature on steam era main lines for over 100 years; this kit contains parts to make 370mm of troughs and includes relevant signboards. Use in conjunction with the Large Water Tower (Ref 256). Glue and paints are required to complete this model.

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint; Weighing Deck 85mm x 50mm, hut 45mm x 35mm.

Many goods yards had weigh bridges so that the 'carriage price' of a load to be carried by rail could be costed. Goods were then loaded into the goods shed. Kit includes guttering, brass etched scales and weighing plate, barge boards, window and door; glue and paints required to complete this model. Footprint: 30mm x 15mm.

If you are a scratchbuilder or want to modify one of our N Gauge kits, this is range for you. Ratio's Builder range has been extended here to include all accessory packs from the Trackside range that you can use to this end. The Builder Series Material Sheet packs contain 4 sheets each 90mm x 75mm

Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model. This pack contains:
‚Ģ 8 x 75mm lengths of fencing
‚Ģ 16 Mounting Posts

2 huts for shelter and tool storage or with many other uses; platelayers huts, tool stores, lamp huts etc. - even garden/allotment sheds or temporary site huts. Glue and paints required to complete model. Footprint: 42mm x 32mm each

A 45mm long replication of a wooden staircase, such as would be used to provide access to a signal box or other raised office/factory areas. Supplied with pre-coloured parts although painting and/or weathering can add realism; glue is required to complete this model.

Used for loading goods onto wagons, these cranes were to be found by bay platforms in small stations with no goods sheds or in the yard of larger stations. The kit includes fine chain for the operating drive wheels and cord for the jib. Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model.

This basic crane is an essential for all station yards, often found inside goods sheds or on loading banks. Used to lift loads up to 1 ton, the boom can be swung round on its base to transfer goods from road to rail vehicles. Supplied with some pre-coloured parts, painting and/or weathering can add realism; glue is required to complete this model. Base Diameter: 25mm

Often, the yard foreman would have an office near the yard gate, for completing paperwork and answering the telephone (don't forget the telegraph poles [Ref 452]!). Supplied with pre-coloured parts although painting and/or weathering can add realism (See the Pecoscene Weathering Powder range PS-360 - 365); glue is required to complete this model. Footprint: 46mm x 30mm.

These specially reinforced ARP (Air Raid Precautions) signal boxes featured substantial construction, primarily to protect the locking room gear from bomb blasts during air raids in World War II. A number of similar signal box designs were still to be found around the rail network until quite recently, due to them being difficult to demolish!
The 554 includes all moulded parts required which are produced to a high standard and in base colours. Kit requires painting and light weathering to create the signal box pictured above.