SORT BY
PAGE

214 Products Found

16 Ton Mineral Wagon Transfers (Waterslide)

Transfers (Waterslide) GWR/BR from Kits PS30-32)

3 Link Couplings

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four pairs of 3- link couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

3 Link Couplings Etched hook Springs

Kit and Scratch builder's accessory. Pack contains 2 pairs of couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

3 Link Instanter Couplings, Hooks, Springs

Kit and Scratch builder's accessory. Pack contains sufficient parts for 2 pairs of Couplings. The "Instanter" coupling is a development of the standard 3 link coupling. The middle link of the chain is specially shaped so that when lying flat it provides enough slack to make coupling possible, but when this middle link is rotated 90 degrees the length of the chain is effectively shortened, reducing the amount of slack to provide closer coupling, to allow the use of train brake pipes without the need to wind a screw. It can also be coupled from the side of the wagons using a shunter's pole; much safer than having to go between vehicles when coupling them together.

3-hole Disc Wheels

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains a pair of metal pin point axles plus bearings, and 3 hole disc wheels featuring free running metal rims on moulded centres.

4 Wheel Box Van

Plastic Kit of typical vehicle based on the Welsh narrow gauge stock from the heyday of the slate traffic era. (Couplings, paint and transfers not included).

4 Wheel Coach Chassis

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customised; also for scratch-building projects. 

4 Wheel Coach Kit, Green

These coach kits comprise chassis components, sides, ends, roof ,duckets, buffers, wheels as illustrated. These versatile kits can be built with or without the guards compartment. 3 body kits could be combined to create a longer bogie coach (bogies not supplied). Supplied in Green livery (couplings, paint, transfers not included).

4 Wheel Coach Kit, Maroon

These coach kits comprise chassis components, sides, ends, roof ,duckets, buffers, wheels as illustrated. These versatile kits can be built with or without the guards compartment. 3 body kits could be combined to create a longer bogie coach (bogies not supplied). Supplied in Maroon livery (couplings, paint, transfers not included).

4 Wheel Open Wagon

Plastic Kit of typical vehicle based on the Welsh narrow gauge stock from the heyday of the slate traffic era. (Couplings, paint and transfers not included).

4 Wheel Wagon Chassis

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customised; also for scratch-building projects. 

4ton Mineral Wagon

White Metal Kit of typical vehicle based on the Welsh narrow gauge stock from the heyday of the slate traffic era. (Couplings, paint and transfers not included).

B' Container Transfers (Pressfix) GWR/BR

Transfers (Pressfix) GWR/BR 'B' Container (from kit PS39)

Banana and Meat Van Transfers (Waterslide)

Transfers (Waterslide) SR/BR (from kits PS100-101)

Beyer-Peacock Tram Locomotive Body

White Metal 0-16.5 body kit of the Beyer-Peacock tramway locomotive , which will look at home on any part of a narrow gauge layout. Fully detailed kit, including shovel and oilcan. Use the Branchlines BL-3 chassis for this kit.

Bicycles (Pack of 6)

Pack of 6 standard type bicycles

Black Background Transfers (Waterslide)

Transfers (Waterslide) Black Background Patches (Pack of 5)

Bolster Set

From Kit PS20

Bolster Wagon 2ton

White Metal Kit of typical vehicle based on the Welsh narrow gauge stock from the heyday of the slate traffic era. (Couplings, paint and transfers not included).

BR 12 ton Pipe Wagon Transfers.

BR 12 ton Pipe Wagon Transfers: 1950s and 1960s/70s periods (from Kit PS17)

BR 12ton Insulated Fish Van

This is a well-known vehicle, derived from the final LNER Fish van design. BR built 1,000 of them. After fish traffic ended they were converted to Parcels Vans (SPV) and lasted into the 1980s. The kit allows both oil and roller bearing axle box versions to be built. Transfers for BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 12ton Pipe Wagon

These wagons were designed to carry heavy cast iron or steel pipes for water and drainage works. This kit represents one of 350 built in 1955. Withdrawn between late 70s and early 80s. Transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 16ton Mineral Wagon

The sloped sided design evolved from pre-1939 private owner wagons built by Chas. Roberts and Co. After the liberation of France 2,500 were shipped over there, 1,900 later returning. Around 10,000 were in stock with BR, with withdrawal taking place in the 1960s. Some ended up private industry use. Transfers for BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 16ton Mineral Wagon

The definitive BR standard mineral wagon produced in vast quantities during the 1950s, and used well in to the 1980s, carrying coal, scrap metal and many different minerals. Parts included for Instanter couplings and double brake gear. Transfers for early, late and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 16ton Mineral Wagon

6,000 were built at the end of the Second World War for service in France. They returned to the UK later in the 1950s and remained in use into the 1960s. Many were then sold into private industry use. Transfers for BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 16ton Welded Steel Mineral Wagon

Built in their hundreds of thousands and seen all over the rail system, these are the wagons which replaced pre war wooden private owner wagons. With side and end doors. Easy to assemble from the correctly coloured injection moulded components (no painting necessary). Kits include Transfers. Buffers are sprung and 3-link couplings are included on all models, while the BR wagons also feature working axlebox springs and moveable brake levers. Fine scale metal tyred wheels on pin-point axles supplied, spoked for the GWR wagons or 3-hole disc for the BR types. Fully illustrated instructions included.

BR 18ton Sand Wagon

A fleet of specialist wagons for industrial and building sand were constructed in the early 1950s. They were designed for emptying by tipper or grab. Withdrawal started in the 1970s, some lasting in Civil Engineers service into the 1980s. Transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 20ton Pig Iron Wagon

These low sided wagons were used for carrying the heavy ingots of crude iron known as 'pigs' from the smelting furnace to the steelworks for refining into steel. Easy to assemble from the correctly coloured injection moulded components (no painting necessary). Kits include Transfers. Buffers are sprung and 3-link couplings are included on all models, while the BR wagons also feature working axlebox springs and moveable brake levers. Fine scale metal tyred wheels on pin-point axles supplied, spoked for the GWR wagons or 3-hole disc for the BR types. Fully illustrated instructions included.

BR 21ton Coal Hopper Wagon

16,800 of these wagons were constructed in the 1950s. They were widely used throughout the North East for the transport of coal. Roller bearing axle boxes were applied to some in the 1960s, options for which are in the kit, and lasted until the 1980s. Transfers for early, late and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 21ton Mineral Wagon

1,500 examples built 1950 – 1951, mainly for the transport of coal. Widely used and lasted until the 1980s. Transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 21ton Trestle Wagon

This design of wagon allowed over-sized steel plates to be carried on a trestle mounted on the wagon. These wagons remained in service into the 1970s. Kit includes securing chains and shackles. Transfers for BR 1950s – 1970s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 24.5ton Mineral Wagon

2,150 of this design were built in 1953 – 1956. Used to carry coal for steel works, power stations and engines sheds. Were intended as the standard mineral wagon, but were too large for many customers. Withdrawn by 1982. Transfers for BR 1950s – 1970s. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 27ton Welded Steel Iron Ore Tippler Wagon

Literally just a steel box on wheels, these wagons were designed to be emptied by turning them upside down in a 'tippler' mechanism, hence there are no side or end doors. Easy to assemble from the correctly coloured injection moulded components (no painting necessary). Kits include Transfers. Buffers are sprung and 3-link couplings are included on all models, while the BR wagons also feature working axlebox springs and moveable brake levers. Fine scale metal tyred wheels on pin-point axles supplied, spoked for the GWR wagons or 3-hole disc for the BR types. Fully illustrated instructions included.

BR Grampus Ballast Wagon

Over 4,000 built from 1951 to 1959, with some in service into the 21st century. Used for carrying ballast and engineer’s materials. Featured fold-down sides for ease of access. Includes etched brass BR region plaques and transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR Mineral Wagon Underframe

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. Pack includes working axlebox springs, sprung buffers, 3 link couplings, floor, full brake gear with alternative types of brake lever and a choice of axleguards.

Branchlines Chassis for Beyer-Peacock Tram Locomotive

The Branchlines (TM) chassis kits featured here are specially designed to fit the Peco 0-16.5 Locomotive Body kits and are complete with wheels and high quality can motors.

Branchlines Chassis for Fletcher Jennings Saddle Tank

The Branchlines (TM) chassis kits featured here are specially designed to fit the Peco 0-16.5 Locomotive Body kits and are complete with wheels and high quality can motors.

Branchlines Chassis for Hunslet Quarry Engine

The Branchlines (TM) chassis kits featured here are specially designed to fit the Peco 0-16.5 Locomotive Body kits and are complete with wheels and high quality can motors.

Brick Base Signal Box

Kit of a typical small box, often found on a branch line or controlling a main line yard.

Buffer Stop, Rail-built

Detailed model of the standard British Railways type. Three plastic moulded parts which, after assembly, clip onto the rails. Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys. This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Buffers NBR (White Metal)

Kit and Scratch builder's accessory. Pack contains sufficient parts for 4 Buffers

Buffers RCH (White Metal)

Kit and Scratch builder's accessory. Pack contains sufficient parts for 4 Buffers

Buffers RCH End Door

Kit and Scratch builder's accessory. Pack contains sufficient parts for 4 Buffers

Bullhead Catch Turnout, Left Hand

The purpose of a Catch Turnout is to derail a vehicle before it rolls out of a siding or branch line on to a main line.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Bullhead Catch Turnout, Right Hand

The purpose of a Catch Turnout is to derail a vehicle before it rolls out of a siding or branch line on to a main line.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Bullhead Crossing, Double Slip

Double slips can save valuable space at station approaches, junctions etc.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Bullhead Crossing, Long

This unit can be used with small, medium, or large radius turnouts to form a double junction.

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

Bullhead curved Turnout, Large Radius, Left Hand

Peco Streamline Bullhead 0 Gauge track has set unsurpassed standards for 7mm scale realism. Superbly detailed, its 'wood grain' sleepers are the correct scale width and have integrally moulded scale chairs with square headed fixing bolts and wooden keys.

This range is compatible with the 0 Setrack range; and if, as on the real network, you wish to use a combination of Bullhead and Flat Bottom track the SL-713 Transition Track provides an ideal way to connect the two types.

PAGE

Trade Login

WOULD YOU LIKE TO BECOME A TRADE PARTNER?

PECO - PLEASE SUPPLY TEXT.
An introductory paragraph with criteria listed as bullets points, closing with contact call to action.