SORT BY
PAGE

214 Products Found

16 Ton Mineral Wagon Transfers (Waterslide)

Transfers (Waterslide) GWR/BR from Kits PS30-32)

3 Link Couplings

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains sufficient components to assemble four pairs of 3- link couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

3 Link Couplings Etched hook Springs

Kit and Scratch builder's accessory. Pack contains 2 pairs of couplings. Three-link chain couplings, with no means of drawing the wagons together, were used to form the peculiarly British "loose coupled" freight train: since such trains were not fitted with an automatic through-train braking system there were no pipes to connect between the vehicles. Control of the train was assisted by the guard's van at the rear of the train, or in certain cases a series of vans spaced along the train, which kept the couplings taut and therefore also helped prevent snapped couplings. Such trains travelled at low speeds and were finally phased out in the 1970s.

3 Link Instanter Couplings, Hooks, Springs

Kit and Scratch builder's accessory. Pack contains sufficient parts for 2 pairs of Couplings. The "Instanter" coupling is a development of the standard 3 link coupling. The middle link of the chain is specially shaped so that when lying flat it provides enough slack to make coupling possible, but when this middle link is rotated 90 degrees the length of the chain is effectively shortened, reducing the amount of slack to provide closer coupling, to allow the use of train brake pipes without the need to wind a screw. It can also be coupled from the side of the wagons using a shunter's pole; much safer than having to go between vehicles when coupling them together.

3-hole Disc Wheels

0 Gauge Chassis kits and Accessories for scratchbuilders and kit modification. This pack contains a pair of metal pin point axles plus bearings, and 3 hole disc wheels featuring free running metal rims on moulded centres.

4 Wheel Box Van

Plastic Kit of typical vehicle based on the Welsh narrow gauge stock from the heyday of the slate traffic era. (Couplings, paint and transfers not included).

4 Wheel Coach Chassis

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects. (Pack of 6)

4 Wheel Coach Kit, Green

These coach kits comprise chassis components, sides, ends, roof ,duckets, buffers, wheels as illustrated. These versatile kits can be built with or without the guards compartment. 3 body kits could be combined to create a longer bogie coach (bogies not supplied). Supplied in Green livery (couplings, paint, transfers not included).

4 Wheel Coach Kit, Maroon

These coach kits comprise chassis components, sides, ends, roof ,duckets, buffers, wheels as illustrated. These versatile kits can be built with or without the guards compartment. 3 body kits could be combined to create a longer bogie coach (bogies not supplied). Supplied in Maroon livery (couplings, paint, transfers not included).

4 Wheel Open Wagon

Plastic Kit of typical vehicle based on the Welsh narrow gauge stock from the heyday of the slate traffic era. (Couplings, paint and transfers not included).

4 Wheel Wagon Chassis

0-16.5 Coach parts to enable the OR-31 and OR-32 Coach kits to be customized; also for scratchbuilding projects. (Pack of 6)

4ton Mineral Wagon

White Metal Kit of typical vehicle based on the Welsh narrow gauge stock from the heyday of the slate traffic era. (Couplings, paint and transfers not included).

B' Container Transfers (Pressfix) GWR/BR

Transfers (Pressfix) GWR/BR 'B' Container (from kit PS39)

Banana and Meat Van Transfers (Waterslide)

Transfers (Waterslide) SR/BR (from kits PS100-101)

Beyer-Peacock Tram Locomotive Body

White Metal 0-16.5 body kit of the Beyer-Peacock tramway locomotive , which will look at home on any part of a narrow gauge layout. Fully detailed kit, including shovel and oilcan. Use the Branchlines BL-3 chassis for this kit.

Bicycles (Pack of 6)

Pack of 6 standard type bicycles

Black Background Transfers (Waterslide)

Transfers (Waterslide) Black Background Patches (Pack of 5)

Bolster Set

From Kit PS20

Bolster Wagon 2ton

White Metal Kit of typical vehicle based on the Welsh narrow gauge stock from the heyday of the slate traffic era. (Couplings, paint and transfers not included).

BR 12 ton Pipe Wagon Transfers.

BR 12 ton Pipe Wagon Transfers: 1950s and 1960s/70s periods (from Kit PS17)

BR 12ton Insulated Fish Van

This is a well-known vehicle, derived from the final LNER Fish van design. BR built 1,000 of them. After fish traffic ended they were converted to Parcels Vans (SPV) and lasted into the 1980s. The kit allows both oil and roller bearing axle box versions to be built. Transfers for BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 12ton Pipe Wagon

These wagons were designed to carry heavy cast iron or steel pipes for water and drainage works. This kit represents one of 350 built in 1955. Withdrawn between late 70s and early 80s. Transfers for early and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 16ton Mineral Wagon

The sloped sided design evolved from pre-1939 private owner wagons built by Chas. Roberts and Co. After the liberation of France 2,500 were shipped over there, 1,900 later returning. Around 10,000 were in stock with BR, with withdrawal taking place in the 1960s. Some ended up private industry use. Transfers for BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

BR 16ton Mineral Wagon

The definitive BR standard mineral wagon produced in vast quantities during the 1950s, and used well in to the 1980s, carrying coal, scrap metal and many different minerals. Parts included for Instanter couplings and double brake gear. Transfers for early, late and post-TOPS BR. These finely moulded plastic wagon kits come complete with pin point axle wheels and bearings, 3 link couplings and transfers. This kit is supplied with pre-coloured moulded parts although painting can improve the appearance. Additional parts to enable the vehicle to be modelled incorporating modifications made to the prototypes during their working life are included where appropriate.

PAGE

Trade Login

WOULD YOU LIKE TO BECOME A TRADE PARTNER?

PECO - PLEASE SUPPLY TEXT.
An introductory paragraph with criteria listed as bullets points, closing with contact call to action.